Difference between revisions of "Tp smapi"

Latest revision as of 09:29, 1 May 2016

The tp_smapi kernel module exposes some features of the ThinkPad hardware/firmware via a sysfs interface. Currently, the main implemented functionality is control of battery charging and extended battery status. The tp_smapi software package also includes an improved version of the HDAPS driver. The underlying hardware interfaces are SMAPI and direct access to the embedded controller.

This driver uses undocumented features and direct hardware access, so it may work unreliably or even damage your hardware; but so far no such damage has been reported.

If you are installing on a recent Thinkpad that has an Ivy Bridge or newer processor (X230, T430, T530, etc.), tp_smapi will not work. You will be mostly limited to thinkpad-acpi capabilities. You can however set battery charge thresholds with tpacpi-bat.

Features

tp_smapi driver
- Battery charge/discharge control
- Battery status information
hdaps driver (compared with the standard hdaps driver)
- Improved stability
- Improved model support
- Improved functionality

Project Homepage / Availability

Project page: http://tpctl.sourceforge.net/
Download page: http://sourceforge.net/projects/tpctl/files/tp_smapi, a newer version 0.41 is available in a fork at https://github.com/evgeni/tp_smapi which is also available in Debian
You need to download only the tp_smapi package.

Installation

Installation from source

You will need the kernel headers and makefiles corresponding to your current kernel version. On Fedora, this means # yum install kernel-devel-$(uname -r) .

# tar xzvf tp_smapi-0.40.tgz

# cd tp_smapi-0.40

Then, either compile and load the driver within the current working directory (for testing):

# make load

OR compile and install into the kernel's module path:

# make install

If you use the HDAPS driver, add HDAPS=1 to also patch the hdaps for compatibility with tp_smapi (this requires a kernel source tree matching the current kernel). Again, either load the driver within the current working directory:

# make load HDAPS=1

OR install into the kernel's module path:

# make install HDAPS=1

To prepare a stand-alone patch against the current kernel tree (including a patch against hdaps and new Kconfig entries):

# make patch

To delete all autogenerated files:

# make clean

The original kernel tree is never modified by any these commands. The /lib/modules directory is modified only by # make install.

Installation in Gentoo

The Gentoo portage system carries a tp_smapi package, which follows the latest version pretty closely. On a Gentoo system, you can install and load as follows.

If you use the HDAPS driver, do this first:

Disable the hdaps module in your kernel configuration (Device Drivers → Hardware Monitoring Support → IBM Hard Drive Active Protection System)
Rebuild and install the kernel
Add the hdaps use flag in /etc/make.conf
# rmmod hdaps

Then:

# emerge tp_smapi (or install tp_smapi with hdaps support manually, as above)
# echo "tp_smapi" >> /etc/modules.autoload.d/kernel-2.6
# echo "hdaps" >> /etc/modules.autoload.d/kernel-2.6

Then reboot, or run:

# modprobe tp_smapi
# modprobe hdaps

NOTE: If # modprobe fails and dmesg says something about __stack_chk_fail(), you probably just compiled your modules with -fstack-protector and/or -fstack-protector-all without having a kernel that supports it. You can either configure your kernel to have CC_STACKPROTECTOR enabled (in Processor type and features if you use # make menuconfig) or edit your make.conf (or, if you're using paludis, your /etc/paludis/bashrc) and remove -fstack-protector and -fstack-protector-all from your CFLAGS. If you choose to enable it in the kernel, be aware that you need a patched GCC for it (and I do not know if the gcc in stage3 is patched).

Installation on Debian and Ubuntu

Since Debian 7 Wheezy and Ubuntu 12.04 Precise you can use 'dkms'. (Note: If installation seems ineffective, confirm you have the linux-headers of your kernel installed, purge tp-smapi-dkms and reinstall.)

# apt-get install linux-headers tp-smapi-dkms
# modprobe tp_smapi

Hint:

This appears to be the ideal solution. A description of DKMS, from Dell: "DKMS stands for Dynamic Kernel Module Support. It is designed to create a framework where kernel dependent module source can reside so that it is very easy to rebuild modules as you upgrade kernels."

Installation on openSUSE

openSUSE provides rpm packages. Look for them at the package search: [1], search for the package named "tp_smapi".

A step-by-step guide on how a relative linux newbie installed tp_smapi on a Thinkpad W500 running openSuse 11.1 using YAST Software Manager is available here

In case you are taking the hard way around, while compiling on 11.0, make complained about not being able to locate the kernel sources. It worked for me after I did this:

cp /usr/include/linux/aio_abi.h /lib/modules/`uname -r`/build/include/linux/

Battery charge control features

NOTE!

Not all Thinkpad ECs support these charge control features. If you get the message "Operation not supported" when trying to cat for the status of a given parameter, it means your controller does not support that feature.

To set the thresholds for starting and stopping battery charging (in percent of current full charge capacity):

# echo 40 > /sys/devices/platform/smapi/BAT0/start_charge_thresh

# echo 70 > /sys/devices/platform/smapi/BAT0/stop_charge_thresh

# cat /sys/devices/platform/smapi/BAT0/*_charge_thresh

Hint:

Battery charging thresholds can be used to keep Li-Ion and Li-Polymer batteries partially charged, in order to increase their lifetime.

To prevent charging for 17 minutes (regardless of thresholds):

# echo 17 > /sys/devices/platform/smapi/BAT0/inhibit_charge_minutes

Hint:

Charge inhibiting can be used to reduce the power draw of the laptop, in order to use an under-spec power supply that can't handle the combined power draw of running and charging. It can also be used to control which battery is charged when using an Ultrabay battery.

To cancel charging preventation:

# echo 0 > /sys/devices/platform/smapi/BAT0/inhibit_charge_minutes

To force battery discharging (even if connected to AC):

# echo 1 > /sys/devices/platform/smapi/BAT0/force_discharge

Hint:

This can be used to choose which battery is discharged when using an UltraBay battery. For example, see the tp-bat-balance (download) script.

To cancel forced discharge:

# echo 0 > /sys/devices/platform/smapi/BAT0/force_discharge

Hint:

TPBattStat-Applet is a gnome applet for integrating battery balancing with a graphics and/or text display of both batteries in a panel. Battery balancing improves battery life by not leaving one battery empty while the other discharges. For the latest alpha release, see https://github.com/teleshoes/tpbattstat-applet

Making the settings permanent on reboot

If you always use the same type of battery, then you may want the same settings to be configured each time you boot the machine.

If you use various types of battery, then you may want to consider writing some scripts to detect the battery type and apply the appropriate settings.

Debian

It is not necessary to create your own init.d script or modify /etc/rc.local - you just need the package sysfsutils:

# apt-get install sysfsutils

Now, put your desired settings in /etc/sysfs.conf:

# cat >> /etc/sysfs.conf << EOF
# For a LiIon battery in a Thinkpad
devices/platform/smapi/BAT0/start_charge_thresh = 50
devices/platform/smapi/BAT0/stop_charge_thresh = 80
EOF

The init script supplied by sysfsutils will load these settings on each boot.

Battery status features

To view extended battery status such as charging state, voltage, current, capacity, cycle count and model information:

# cat /sys/devices/platform/smapi/BAT0/installed
# cat /sys/devices/platform/smapi/BAT0/state       # idle/charging/discharging
# cat /sys/devices/platform/smapi/BAT0/cycle_count
# cat /sys/devices/platform/smapi/BAT0/current_now # instantaneous current
# cat /sys/devices/platform/smapi/BAT0/current_avg # last minute average
# cat /sys/devices/platform/smapi/BAT0/power_now   # instantaneous power
# cat /sys/devices/platform/smapi/BAT0/power_avg   # last minute average
# cat /sys/devices/platform/smapi/BAT0/last_full_capacity
# cat /sys/devices/platform/smapi/BAT0/remaining_percent
# cat /sys/devices/platform/smapi/BAT0/remaining_running_time
# cat /sys/devices/platform/smapi/BAT0/remaining_charging_time
# cat /sys/devices/platform/smapi/BAT0/remaining_capacity
# cat /sys/devices/platform/smapi/BAT0/design_capacity
# cat /sys/devices/platform/smapi/BAT0/voltage
# cat /sys/devices/platform/smapi/BAT0/design_voltage
# cat /sys/devices/platform/smapi/BAT0/manufacturer
# cat /sys/devices/platform/smapi/BAT0/model
# cat /sys/devices/platform/smapi/BAT0/barcoding
# cat /sys/devices/platform/smapi/BAT0/chemistry
# cat /sys/devices/platform/smapi/BAT0/serial
# cat /sys/devices/platform/smapi/BAT0/manufacture_date
# cat /sys/devices/platform/smapi/BAT0/first_use_date
# cat /sys/devices/platform/smapi/BAT0/temperature # in milli-Celsius
# cat /sys/devices/platform/smapi/ac_connected

The raw status data is also available, including some fields not listed above (in case you can figure them out):

# cat /sys/devices/platform/smapi/BAT0/dump

In all of the above, replace BAT0 with BAT1 to address the 2nd battery.

Note that the battery status readout conflicts with the stock hdaps driver, so if you use hdaps you will need to load tp_smapi using # make load HDAPS=1 (see Bundled hdaps driver below).

On ACPI-enabled systems, most of above information is also available through the files under /proc/acpi/battery. However, the ACPI interface does not include the instantaneous power and cycle count readouts, and does not work well when hotswapping UltraBay batteries.

Scripts

Some scripts can make it easier to grep the information you need from tp_smapi

battery.rb

Other features

There is also sysfs attribute for making direct SMAPI requests to the SM BIOS firmware. Don't touch it unless you really know what you're doing. Example:

# echo '211a 100 0 0' > /sys/devices/platform/smapi/smapi_request; cat /sys/devices/platform/smapi/smapi_request
211a 34b b2 0 0 0 'OK'

The "4b" in the 2nd value, converted to decimal, is 75: the current charging stop threshold (stop_charge_thresh).

Bundled `hdaps` driver

The tp_smapi package includes a modified version of the hdaps Linux kernel driver used by the HDAPS system. It has remained outside the mainline kernel for a few years for several reasons, [2] including the upstream maintainer's assertion that the new code's anonymous author was under a NDA. (Although this would not normally expose the kernel team to litigation.) [3] [4] [5]

To use tp_smapi and hdaps concurrently, you must use the modified version.

To build the modified version, simply append the HDAPS=1 parameter to the make command (see Installation above):

# make load HDAPS=1

or

# make install HDAPS=1

If you don't do that, you will not be able to load tp_smapi (and its support module thinkpad_ec) when hdaps is loaded, and vice versa. You can use rmmod to switch between these modules.

Note that some of the battery status is also visible through ACPI (/proc/acpi/battery/*), independently of tp_smapi.

The modified hdaps has several changes:

The hdaps driver in mainline kernels conflicts with the extended battery status (they use the same IO ports). The modified hdaps coordinates this access through the bundled thinkpad_ec driver.
The modified hdaps driver fixes reliability and improves support for recent ThinkPad models (*60 and newer), since unlike the mainline driver, it correctly follows the Embedded Controller communication protocol.
Several other improvements, such as the ability to control the polling rate.

Troubleshooting

`thinkpad_ec: cannot claim io ports 0x1600-0x161f`

The "thinkpad_ec: cannot claim io ports 0x1600-0x161f!" error message is printed when loading the thinkpad_ec module on some recent ThinkPad models. This occurs because the ACPI BIOS DSDT is reserving ports used by tp_smapi.

As a workaround, add the force_io=1 module parameter to thinkpad_ec in /etc/modprobe.conf (or your distribution's equivalent). Add the line:

options thinkpad_ec force_io=1

For transient testing, load the modules as follows:

# make load HDAPS=1 FORCE_IO=1

Note: force_io option was added in tp_smapi v0.40 (released 2008-12-16).

Models which need this option include: T400, T500, X60s, X61, X301

More information:

`thinkpad_ec: no ThinkPad embedded controller!`

If you get "thinkpad_ec: no ThinkPad embedded controller!" when trying to load the module on a supported model listed below, you should upgrade your BIOS. Some early BIOS (like 1.x on the X31) don't handle the embedded controller.

`T60p writing to start_charge_thresh/stop_charge_thresh does not work!`

Writing to /sys/devices/platform/smapi/BAT0/start_charge_thresh succeeds, but the older value does not change. Solution: unknown. If you know a solution please update here.

UPDATE: Failure to effectively change sysfs values sometimes happens at boot time (through sysfs.conf OR etc/local.start for instance) when the values have never previously been changed manually (ie using echo from a shell). Try initializing the values manually before including them in boot-time scripting.

Model-specific status

Tip: The thinkpad-acpi module reports both the BIOS and EC firmware versions when it loads.

`tp_smapi` feature support matrix
A series
Model and machine type	`start_ charge_ thresh`	`stop_ charge_ thresh`	`inhbit_ charge_ minutes`	`force_ discharge`	battery status files	Bundled HDAPS	HDAPS axis orientation¹	tp_smapi version	BIOS version	EC firmware version	Notes
A22p 2629-USG	no	no	no	no	no	N/A	N/A
A30	no	no	no	no	yes	N/A	N/A
G series
Model and machine type	`start_ charge_ thresh`	`stop_ charge_ thresh`	`inhbit_ charge_ minutes`	`force_ discharge`	battery status files	Bundled HDAPS	HDAPS axis orientation¹	tp_smapi version	BIOS version	EC firmware version	Notes
G41	yes	no	yes	unknown	unknown	N/A	N/A
R series
Model and machine type	`start_ charge_ thresh`	`stop_ charge_ thresh`	`inhbit_ charge_ minutes`	`force_ discharge`	battery status files	Bundled HDAPS	HDAPS axis orientation¹	tp_smapi version	BIOS version	EC firmware version	Notes
R31	no	no	no	no	no	N/A	N/A				No SMAPI BIOS
R40	no	no	no	no	unknown	N/A	N/A
R50	unknown	no	unknown	unknown	yes	unknown	unknown
R50e 1834-JAG	yes	no	yes	yes	yes	N/A	N/A
R50e 1834-5US	yes	no	yes	yes	yes	N/A	N/A
R50p	no	no	no	no	yes	unknown	unknown
R51 18*	yes	no	yes	yes	yes	yes	0	0.32	3.22		Machine types 1829, 1830, 1831 and 1836
R51 28*	yes	no	yes	unknown	yes	unknown	unknown		1.29		Machine types 2883, 2887, 2888, 2889, 2894 and 2495
R52	yes	yes	yes	yes	yes	yes	0	0.33	1.29	1.06
R60	yes	yes	yes	yes	yes	yes	1	0.33
R61	yes	yes	unknown	unknown	yes	yes	1	0.35-test1	7KETA7WW 2.07	7KHT24WW 1.08	Machine type 8918
R61i	yes	yes	yes	yes	yes	yes	1	0.41			Machine types 7732, 8250
R400	yes	yes	yes	yes	yes	yes	1	0.40-1			Machine type 7443
R500	yes	yes	unknown	unknown	yes	unknown	1	0.40-1
T series
Model and machine type	`start_ charge_ thresh`	`stop_ charge_ thresh`	`inhbit_ charge_ minutes`	`force_ discharge`	battery status files	Bundled HDAPS	HDAPS axis orientation¹	tp_smapi version	BIOS version	EC firmware version	Notes
T20	no	no	no	no	no	N/A	N/A				Has SMAPI BIOS but no function is supported. EC LPC3 protocol fails.
T22	no	no	no	no	no	N/A	N/A				Has SMAPI BIOS but no function is supported. EC LPC3 protocol fails.
T23	no	no	no	no	yes	N/A	N/A
T30	no	no	no	no	yes	N/A	N/A
T40	no	no	no	no	yes	N/A	N/A
T40 2373-72U	no	no	no	no	yes	N/A	N/A	0.40	3.23	1RHT71WW-3.04
T40p	no	no	no	no	yes	N/A	N/A
T41	no	no	no	no	yes	unknown	unknown	0.37	3.23	3.04
T41	no	no	no	no	yes	unknown	unknown	0.40	3.20	3.04
T41	no	no	no	no	yes	unknown	unknown	0.40	3.23	3.04
T41p 2373-AM9	no	no	no	no	yes	yes	1	0.32	3.20	v3.04
T42	yes	no	yes	yes	yes	unknown	unknown
T42p 2373-KXU	yes	no	yes	yes	yes	yes	1	0.32	3.21		Stop charge threshold works in Windows, but dmesg says "__get_real_thresh: cannot get stop_thresh of bat=0: Function is not supported by SMAPI BIOS".
T42p 2373-KUU	yes	no	yes	unknown	yes	unknown	unknown
T43 2686	yes	yes	yes	yes	yes	yes	0	0.33	1.27
T43p	yes	yes	yes	yes	yes	unknown	0
T60	yes	yes	unknown	yes	yes	yes	7	0.32
T60	yes	yes	unknown	yes	yes	yes	1	0.34
T60 1951-24G	yes	yes	unknown	yes	yes	yes	unknown	0.36	1.09a
T60 2007-FSG	yes	yes	yes	yes	yes	unknown	unknown	0.39	1.10	1.05b
T60 1951-CZ1	yes	yes	yes	yes	yes	yes	1	0.40	2.23	1.07
T60p 8743-CTO	yes	yes	yes	yes	yes	yes	1	0.32
T61	yes	yes	yes	yes	yes	yes	1	0.32			ref
T61p 6457-7XG	yes	yes	yes	yes	yes	yes	1	0.32			ref
T400	yes	yes	yes	yes	yes	yes	1	0.40	1.19		Requires `force_io=1` parameter to `thinkpad_ec`
T400s	yes	yes	yes	yes	yes	yes	2	0.40	1.06		Requires `invert=2` paramteter to `hdaps`
T410s	yes	yes	yes	unknown	yes	yes	4	0.40	1.14		Requires `invert=4` accoding to `hdaps-gl`
T410	yes	yes	yes	yes	yes	yes	1	0.40	1.25
T500	yes	yes	yes	yes	yes	yes	1	0.40	2.07		Requires `force_io=1` parameter to `thinkpad_ec`
T510	yes	yes	yes	yes	yes	yes	7	0.40	1.12	1.08
T510	yes	yes	yes	yes	yes	yes	7	0.40	1.35	1.17
W series
Model and machine type	`start_ charge_ thresh`	`stop_ charge_ thresh`	`inhbit_ charge_ minutes`	`force_ discharge`	battery status files	Bundled HDAPS	HDAPS axis orientation¹	tp_smapi version	BIOS version	EC firmware version	Notes
W700 2757-CTO	yes	yes	yes	yes	yes	unknown	unknown	0.40	2.08	1.05
W500 4062-4EG	yes	yes	unknown	unknown	unknown	unknown	unknown	0.40	unknown	unknown
X series
Model and machine type	`start_ charge_ thresh`	`stop_ charge_ thresh`	`inhbit_ charge_ minutes`	`force_ discharge`	battery status files	Bundled HDAPS	HDAPS axis orientation¹	tp_smapi version	BIOS version	EC firmware version	Notes
X22	no	no	no	no	no	N/A	N/A				no EC controller found
X24	no	no	no	unknown	yes	N/A	N/A
X30	no	no	no	no	yes	N/A	N/A	0.34	1.09
X31	no	no	no	no	yes	N/A	N/A	0.40	3.02
X32	no	no	no	no	yes	N/A	N/A
X40	yes	yes	yes	yes	yes	yes	3	0.32	2.08	1.62
X41	yes	yes	yes	yes	yes	yes	3	0.32
X41 Tablet	yes	yes	yes	yes	yes	yes	3	0.40	75ET60WW (2.06 )	75HT20WW (1.02)
X60	yes	yes	yes	yes	yes	yes	6		2.07	1.10	2.6.20 issue (see discussion)
X60 Tablet	yes	yes	yes	yes	yes	yes	3	0.34	7JET25WW (1.10 )	7JHT13WW 1.04	ref ref
X60s 1704-5UG	yes	yes	unknown	unknown	unknown	unknown	3	0.34	7BETD2WW 2.13	7BHT40WW 1.13
X60s 1704-56G	yes	yes	yes	unknown	yes	unknown	3	0.40	7BETD5WW 2.16	7BHT40WW 1.13
X61 7673-CTO	yes	yes	yes	yes	yes	yes	6	0.40	7NETB9WW (2.19)	7MHT25WW-1.03
X61 7675-4KU	yes	yes	yes	yes	yes	yes	6	0.34	7NET30WW (1.11 )	7MHT24WW 1.02
X61 Tablet	yes	yes	unknown	unknown	yes	yes	6	0.32
X61s	yes	yes	yes	yes	yes	yes	6 / 3	0.32			ref says 3 but conflicting report received
X100e	yes	yes	yes	yes	yes	unknown	unknown	0.40	6XET36WW (1.20a)	6XHT36WW (1.176000)	x100e NTS4UTX, dual-core L625 also works (NTT27MH)
X120e	no	yes	yes	no	yes	unknown	unknown	0.41	8FET32WW (1.16 )	unknown	model 0596CTO
X200	yes	yes	yes	yes	yes	yes	7	0.40	6DET40WW (2.04 )	7XHT22WW 1.04
X200s 7470-X01	yes	yes	unknown	unknown	yes	yes	5	0.40	6DET63WW (3.13)	7XHT24WW 1.06
X201	yes	yes	unknown	unknown	yes	yes	6 / 5	0.40		ECP:	It said 6 here, but see discussion page
X201s	yes	yes	unknown	unknown	yes	yes	5	0.40	6QET44WW (1.14 )	ECP: 1.09/1.09
X220 4290-2GW	no	no	no	no	no	no	no	0.40	8DET46WW (1.16 )	"unknown"
X220 4286-CTO	no	yes	yes	no	yes	yes	unknown	0.41	8DET54WW (1.24 )	unknown	HDAPS works fine, don't know wich axis orientation thougth
X300	yes	yes	yes	unknown	yes	yes	unknown	0.37	7TET25WW (1.02 )	7THT15WW 1.00c
Z series
Model and machine type	`start_ charge_ thresh`	`stop_ charge_ thresh`	`inhbit_ charge_ minutes`	`force_ discharge`	battery status files	Bundled HDAPS	HDAPS axis orientation¹	tp_smapi version	BIOS version	EC firmware version	Notes
Z60m	yes	yes	yes	yes	yes	unknown	unknown
Z60t	yes	yes	unknown	unknown	yes	unknown	unknown
Z61m	yes	yes	yes	yes	yes	yes	0	0.32
Z61t	yes	yes	yes	yes	yes	yes	unknown				ref
Z61p	yes	yes	unknown	yes	yes	yes	unknown
SL series and IdeaPad
The ThinkPad SL series and IdeaPad series have firmware that is completely different from other ThinkPad models. Neither tp_smapi nor thinkpad-acpi support these models.

SMAPI capabilities may depend on the BIOS version as well, so upgrading to the latest version of the BIOS might provide more SMAPI functions (especially true for long-lived BIOS with lots of releases, like the TP-1R).

Please update the above and report your experience on the discussion page. If the module loads but gives a "not supported" or "not implementeded" error when you try to use some specific file in /sys/devices/platform/smapi/, please report the dmesg output and whether the corresponding functionality is available under Windows - maybe your ThinkPad just can't do that.

While at it, you may also want to add your laptop to the list of DMI IDs.

HDAPS axis orientation

¹ The HDAPS axis orientation is set using the invert module parameter (at load time) or sysfs attribute (at runtime). The hdaps driver of tp_smapi supports all 8 possible sensor orientations (inversion and swapping). You can use hdaps visualisation to check if the settings is correct.

The invert parameter is an integer between 0 and 7, whose meaning is defined below. (This is confusing. Most people will find it easier to just try all 8 possibilities.)

Let X and Y denote the hardware readouts. Let R denote the laptop's roll (tilt left/right), and let P denote the laptop's pitch (tilt forward/backward). The possible values are as follows:

   invert=0:   R= X  P= Y   (same as mainline)
   invert=1:   R=-X  P=-Y   (same as mainline)
   invert=2:   R=-X  P= Y   (new)
   invert=3:   R= X  P=-Y   (new)
   invert=4:   R= Y  P= X   (new)
   invert=5:   R=-Y  P=-X   (new)
   invert=6:   R=-Y  P= X   (new)
   invert=7:   R= Y  P=-X   (new)

Tools using this driver

The driver's interface can be accessed directly through the files under /sys/devices/platform/smapi, or via the following tools:

KThinkBat - display battery status on the KDE kicker panel.
gkrellm-ThinkBat - battery status plugin for Gkrellm2
thinkpad-smapi.sh (download) - script to display various SMAPI information using tp_smapi module.

Headline text

@@ Line 5: / Line 5: @@
 This driver uses undocumented features and direct hardware access, so it may work unreliably or even damage your hardware; but so far no such damage has been reported.
+If you are installing on a recent Thinkpad that has an [[Ivy Bridge]] or newer processor ({{X230}}, {{T430}}, {{T530}}, etc.), tp_smapi will not work. You will be mostly limited to [[thinkpad-acpi]] capabilities. You can however set battery charge thresholds with [[tpacpi-bat]].
 |}
@@ Line 18: / Line 20: @@
 ===Project Homepage / Availability===
 * Project page: http://tpctl.sourceforge.net/
+* Download page: http://sourceforge.net/projects/tpctl/files/tp_smapi, a newer version 0.41 is available in a fork at https://github.com/evgeni/tp_smapi which is also available in Debian
 * You need to download only the <i>tp_smapi</i> package.
@@ Line 67: / Line 70: @@
 * {{cmdroot|modprobe hdaps}}
-====Installation on Debian unstable (sid), testing (squeeze) or stable (lenny)====
+'''NOTE:''' If {{cmdroot|modprobe}} fails and dmesg says something about <tt>__stack_chk_fail()</tt>, you probably just compiled your modules with <tt>-fstack-protector</tt> and/or <tt>-fstack-protector-all</tt> without having a kernel that supports it. You can either configure your kernel to have <tt>CC_STACKPROTECTOR</tt> enabled (in ''Processor type and features'' if you use {{cmdroot|make menuconfig}}) or edit your <tt>make.conf</tt> (or, if you're using paludis, your <tt>/etc/paludis/bashrc</tt>) and remove <tt>-fstack-protector</tt> and <tt>-fstack-protector-all</tt> from your <tt>CFLAGS</tt>. If you choose to enable it in the kernel, be aware that you need a patched GCC for it (and I do not know if the gcc in stage3 is patched).
-Debian now contains the [http://packages.debian.org/tp-smapi packaged module source] and prebuilt modules for Debian kernels.
-If you use a stock Debian kernel, you can install the tp_smapi modules with:
-* {{cmdroot|apt-get install tp-smapi-modules-`uname -r`}}
-* in order to make sure the modules package is kept in sync with the kernel one, you may also want to install the <code>tm-smapi-modules-2.6-686</code> or <code>tm-smapi-modules-2.6-amd64</code> package, depending on your architecture
-If you use a custom kernel, you can build tp_smapi with module-assistant:
+====Installation on Debian and Ubuntu====
-* {{cmdroot|aptitude install tp-smapi-source}}
+Since Debian 7 Wheezy and Ubuntu 12.04 Precise you can use 'dkms'. (Note: If installation seems ineffective, confirm you have the linux-headers of your kernel installed, purge tp-smapi-dkms and reinstall.)
-* {{cmdroot|m-a -t a-i tp-smapi}}
+* {{cmdroot|apt-get install linux-headers tp-smapi-dkms}}
+* {{cmdroot|modprobe tp_smapi}}
-====Installation on Ubuntu Hardy====
+{{HINT|This appears to be the ideal solution. A description of DKMS, from [http://linux.dell.com/projects.shtml#dkms Dell]: "DKMS stands for Dynamic Kernel Module Support. It is designed to create a framework where kernel dependent module source can reside so that it is very easy to rebuild modules as you upgrade kernels."}}
-Ubuntu ships tp_smapi in their linux-ubuntu-modules Package since Hardy, so you don't have to build it yourself. Please note that they have renamed tp_smapi's modified <tt>hdaps</tt> module to <tt>hdaps_ec</tt>. You should load <tt>hdaps_ec</tt>, not <tt>hdaps</tt>.
-Some Ubuntu packages lack the <tt>hdaps_ec</tt> module, as reported [https://bugs.launchpad.net/ubuntu/+source/linux/+bug/297213 here].
+====Installation on openSUSE====
+openSUSE provides rpm packages. Look for them at the package search: [http://software.opensuse.org/search/], search for the package named "tp_smapi".
-====Installation on older Ubuntu/Debian====
+A step-by-step guide on how a relative linux newbie installed tp_smapi on a Thinkpad W500 running openSuse 11.1 using YAST Software Manager is available [http://forums.opensuse.org/hardware/laptop/417254-tp_smapi-lenovo-thinkpad-t400-t500-w500-step-step.html#post2005932 here]
-Installation on Ubuntu or Debian is quite easy, but there are a few things to look after:
-To get your system ready for compiling code, install the build-essentials (as root, of course, as all of the following comands; Ubuntu users have to prepend 'sudo' to every line and enter their own password when prompted):
+In case you are taking the hard way around, while compiling on 11.0, make complained about not being able to locate the kernel sources. It worked for me after I did this:
-<pre><nowiki>apt-get install build-essential</nowiki></pre>
+<pre><nowiki>cp /usr/include/linux/aio_abi.h /lib/modules/`uname -r`/build/include/linux/</nowiki></pre>
-To get tp_smapi to work, obtain the latest source as mentioned above and unpack it. If you want to use HDAPS, you need to install the kernel source matching te kernel you are running. To do so, issue this:
+===Battery charge control features===
-<pre><nowiki>uname -r</nowiki></pre>
+{{NOTE|Not all Thinkpad ECs support these charge control features. If you get the message "Operation not supported" when trying to cat for the status of a given parameter, it means your controller does not support that feature.}}
-This will give you the version of your current kernel.
-Debian users execute the following:
-<pre><nowiki>apt-get install linux-source-`uname -r`</nowiki></pre>
-Ubuntu users execute the following using the kernel-version only (exclude -XX-generic; e.g. 'linux-source-2.6.20'):
-<pre><nowiki>apt-get install linux-source-`uname -r`</nowiki></pre>
-Be sure to unpack the source file. The easiest way is to open Nautilus as root:
-<pre><nowiki>sudo nautilus</nowiki></pre>
-Then browse to /usr/src/ and extract the source file to that directory.
-Now change to the tp_smapi dir:
-<pre><nowiki>cd tp_smapi-X.YY</nowiki></pre> (X.YY being the version-number of [[tp_smapi]])
-and make and install tp_smapi as instructed above.
-If you get an error that the kernel version isn't matching (or that you need to set KSRC/KBUILD), please check that there is a symlink from the modules dir to the kernel source:
-<pre><nowiki>root@localhost:~#ls -l /lib/modules/2.6.20-16-generic
-lrwxrwxrwx  1 root root     28 2007-02-02 08:39 build -> /usr/src/linux-source-2.6.20</nowiki></pre>
-Create the link if the line above is not existent:
-<pre><nowiki>root@localhost:~#ln -s /usr/src/linux-source-2.6.20 /lib/modules/2.6.20-16-generic/build</nowiki></pre>
-Now the following will build and install the correct modules to their locations:
-<pre><nowiki>make install HDAPS=1</nowiki></pre>
-To make sure your system loads the modules at boot time, do this:
-<pre><nowiki>echo "tp_smapi" >> /etc/modules
-echo "hdaps" >> /etc/modules</nowiki></pre>
-and update your initramfs:
-<pre><nowiki>update-initramfs -u</nowiki></pre>
-To get tp_smapi running now, just load the modules:
-<pre><nowiki>modprobe -a tp_smapi hdaps</nowiki></pre>
-This description was tested on Kubuntu 'Feisty Fawn' and should work on all Debian-based distros with minor tweaks.
-'''EDIT:''' Works on Kubuntu 7.10 ("Gutsy Gibbon"), too
-===Battery charge control features===
 To set the thresholds for starting and stopping battery charging (in percent of current full charge capacity):
 :{{cmdroot|echo 40 > /sys/devices/platform/smapi/BAT0/start_charge_thresh}}
 :{{cmdroot|echo 70 > /sys/devices/platform/smapi/BAT0/stop_charge_thresh}}
 :{{cmdroot|cat /sys/devices/platform/smapi/BAT0/*_charge_thresh}}
-{{HINT|Battery charging thresholds can be used to keep Li-Ion ad Li-Polymer batteries partially charged, in order to [[Maintenance#Battery_treatment|increase their lifetime]].}}
+{{HINT|Battery charging thresholds can be used to keep Li-Ion and Li-Polymer batteries partially charged, in order to [[Maintenance#Battery_treatment|increase their lifetime]].}}
 To prevent charging for 17 minutes (regardless of thresholds):
 :{{cmdroot|echo 17 > /sys/devices/platform/smapi/BAT0/inhibit_charge_minutes}}
@@ Line 141: / Line 105: @@
 To force battery discharging (even if connected to AC):
 :{{cmdroot|echo 1 > /sys/devices/platform/smapi/BAT0/force_discharge}}
-{{HINT|This can be used to choose which battery is discharged when [[How to use UltraBay batteries|using an UltraBay battery]].}}
+{{HINT|This can be used to choose which battery is discharged when [[How to use UltraBay batteries|using an UltraBay battery]]. For example, see the {{CodeRef|tp-bat-balance}} script.}}
 To cancel forced discharge:
 :{{cmdroot|echo 0 > /sys/devices/platform/smapi/BAT0/force_discharge}}
+{{HINT|TPBattStat-Applet is a gnome applet for integrating battery balancing with a graphics and/or text display of both batteries in a panel. Battery balancing improves battery life by not leaving one battery empty while the other discharges. For the latest alpha release, see https://github.com/teleshoes/tpbattstat-applet}}
+====Making the settings permanent on reboot====
+If you always use the same type of battery, then you may want the same settings to be configured each time you boot the machine.
+If you use various types of battery, then you may want to consider writing some scripts to detect the battery type and apply the appropriate settings.
+=====Debian=====
+It is not necessary to create your own init.d script or modify /etc/rc.local - you just need the package sysfsutils:
+:{{cmdroot|apt-get install sysfsutils}}
+Now, put your desired settings in /etc/sysfs.conf:
+<pre><nowiki># cat >> /etc/sysfs.conf << EOF
+# For a LiIon battery in a Thinkpad
+devices/platform/smapi/BAT0/start_charge_thresh = 50
+devices/platform/smapi/BAT0/stop_charge_thresh = 80
+EOF</nowiki></pre>
+The init script supplied by sysfsutils will load these settings on each boot.
 ===Battery status features===
@@ Line 199: / Line 186: @@
 ===Bundled <tt>hdaps</tt> driver===
-The tp_smapi package includes a modified version of the <tt>hdaps</tt> Linux kernel driver used by the [[HDAPS]] system. To use <tt>tp_smapi</tt> and <tt>hdaps</tt> concurrently, you '''must''' use the modified version.
+The tp_smapi package includes a modified version of the <tt>hdaps</tt> Linux kernel driver used by the [[HDAPS]] system. It has remained outside the mainline kernel for a few years for several reasons, [https://lists.ubuntu.com/archives/kernel-team/2009-April/005565.html] including the upstream maintainer's assertion that the new code's anonymous author was under a NDA. (Although this would not normally expose the kernel team to litigation.) [http://lkml.org/lkml/2008/9/15/126] [http://lkml.org/lkml/2008/10/7/403] [http://lkml.org/lkml/2008/10/7/428]
+To use <tt>tp_smapi</tt> and <tt>hdaps</tt> concurrently, you '''must''' use the modified version.
 To build the modified version, simply append the <tt>HDAPS=1</tt> parameter to the <tt>make</tt> command (see [[#Installation|Installation]] above):
@@ Line 219: / Line 208: @@
 The "<tt>thinkpad_ec: cannot claim io ports 0x1600-0x161f!</tt>" error message is printed when loading the <tt>thinkpad_ec</tt> module on some recent ThinkPad models.  This occurs because the ACPI BIOS DSDT is reserving ports used by tp_smapi.
-As a workaround, add the <tt>force_io=1</tt> module parameter to <tt>thinkpad_ec</tt> in {{path|/etc/modprobe.conf}} (or your distribution's equivalent). For transient testing, load the modules as follows:
+As a workaround, add the <tt>force_io=1</tt> module parameter to <tt>thinkpad_ec</tt> in {{path|/etc/modprobe.conf}} (or your distribution's equivalent). Add the line:
+: options thinkpad_ec force_io=1
+For transient testing, load the modules as follows:
 : {{cmdroot|1=make load HDAPS=1 FORCE_IO=1}}
@@ Line 225: / Line 217: @@
 Note: force_io option was added in tp_smapi v0.40 (released 2008-12-16).
-Models which need this option include:
+Models which need this option include: {{T400}}, {{T500}}, {{X60s}}, {{X61}}, {{X301}}
-* ThinkPad {{T400}}
-* ThinkPad {{T500}}
-* ThinkPad {{X301}}
 More information:
@@ Line 236: / Line 225: @@
 ==== <tt>thinkpad_ec: no ThinkPad embedded controller!</tt> ====
 If you get "<tt>thinkpad_ec: no ThinkPad embedded controller!</tt>" when trying to load the module on a supported model listed below, you should [[BIOS_Upgrade|upgrade your BIOS]]. Some early BIOS (like 1.x on the X31) don't handle the embedded controller.
+==== <tt>T60p writing to start_charge_thresh/stop_charge_thresh does not work!</tt> ====
+Writing to /sys/devices/platform/smapi/BAT0/start_charge_thresh succeeds, but the older value does not change. Solution: unknown. If you know a solution please update here.
+UPDATE:  Failure to effectively change sysfs values sometimes happens at boot time (through sysfs.conf OR etc/local.start for instance) when the values have never previously been changed manually (ie using echo from a shell).  Try initializing the values manually before including them in boot-time scripting.
 ===Model-specific status===
+Tip: The <tt>thinkpad-acpi</tt> module reports both the BIOS and EC firmware versions when it loads.
 <div style="font-size: 92%">
@@ Line 244: / Line 239: @@
 |+<tt>tp_smapi</tt> feature support matrix
 |-
 ! colspan=12 style="text-align:center;background:#efefef;" |
 =====A series=====
 |-
@@ Line 256: / Line 252: @@
 |-
 ! colspan=12 style="text-align:center;background:#efefef;" |
 =====G series=====
 |-
@@ Line 303: / Line 300: @@
 |-
 ! {{R61i}}
-| {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cyes}} ||{{Cunk}}  || {{Cunk}}  ||    ||   ||   || Machine type 8250
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} ||{{Cyes}}  || {{Cyes|text=}} 1  || 0.41 ||   ||   || Machine types 7732, 8250
 |-
 ! {{R400}}
-| {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cyes}} ||{{Cunk}}  || {{Cunk}}  || 0.37-6   ||   ||   || Machine type 7443; added pnpacpi=off to grub boot menu.lst; force_io=yes only supported in tp_smapi v0.40
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} ||{{Cyes}}  || {{Cyes|text=}} 1 || 0.40-1   ||   ||   || Machine type 7443
+|-
+! {{R500}}
+| {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cyes}} ||{{Cunk}}  || {{Cyes|text=}} 1 || 0.40-1   ||   ||   ||
 |-
 ! colspan=12 style="text-align:center;background:#efefef;" |
@@ Line 328: / Line 328: @@
 ! {{T40}}
 | {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cyes}} || N/A || N/A ||      ||  || ||
+|-
+! {{T40}} 2373-72U
+| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cyes}} || N/A || N/A ||  0.40  || 3.23  || 1RHT71WW-3.04  ||
 |-
 ! {{T40p}}
@@ Line 334: / Line 337: @@
 ! {{T41}}
 | {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cyes}} || {{Cunk}} || {{Cunk}} || 0.37 || 3.23 || 3.04 ||
+|-
+! {{T41}}
+| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cyes}} || {{Cunk}} || {{Cunk}} || 0.40 || 3.20 || 3.04 ||
+|-
+! {{T41}}
+| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cyes}} || {{Cunk}} || {{Cunk}} || 0.40 || 3.23 || 3.04 ||
 |-
 ! {{T41p}} 2373-AM9
@@ Line 377: / Line 386: @@
 | {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 1 || 0.32 ||  || || [http://ubuntuforums.org/showthread.php?p=3146719 ref]
 |-
 ! {{T400}}
-| {{Cunk}}  || {{Cunk}}  || {{Cunk}}  || {{Cunk}}  || {{Cunk}}  || {{Cunk}}  || {{Cunk}}  1 || 0.40 || 1.19 || || Requires <tt>force_io=1</tt> parameter to <tt>thinkpad_ec</tt>
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes|text=}}  1 || 0.40 || 1.19 || || Requires <tt>force_io=1</tt> parameter to <tt>thinkpad_ec</tt>
+|-
+! {{T400s}}
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes|text=}} 2 || 0.40 || 1.06 || || Requires <tt>invert=2</tt> paramteter to <tt>hdaps</tt>
+|-
+! {{T410s}}
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cunk}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes|text=}} 4 || 0.40 || 1.14 || || Requires <tt>invert=4</tt> accoding to <tt>hdaps-gl</tt>
+|-
+! {{T410}}
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes|text=}}  1 || 0.40 || 1.25 || ||
 |-
 ! {{T500}}
-| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  1 || 0.40 || 2.07 || || Requires <tt>force_io=1</tt> parameter to <tt>thinkpad_ec</tt>
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes|text=}}  1 || 0.40 || 2.07 || || Requires <tt>force_io=1</tt> parameter to <tt>thinkpad_ec</tt>
+|-
+! {{T510}}
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cno|text=}}  7 || 0.40 || 1.12 || 1.08 || ||
+|-
+! {{T510}}
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cno|text=}}  7 || 0.40 || 1.35 || 1.17 || ||
+|-
+! colspan=12 style="text-align:center;background:#efefef;" |
+=====W series=====
+|-
+{{tp_smapi/model_status_table_header}}
+|-
+! {{W700}} 2757-CTO
+| {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cyes}}  || {{Cunk}} || {{Cunk}} ||  0.40 || 2.08 || 1.05 ||
+|-
+! {{W500}} 4062-4EG
+| {{Cyes}}  || {{Cyes}}  || {{Cunk}}  || {{Cunk}}  || {{Cunk}}  || {{Cunk}} || {{Cunk}} ||  0.40 || {{Cunk}} || {{Cunk}} ||
 |-
@@ Line 389: / Line 425: @@
 |-
 {{tp_smapi/model_status_table_header}}
-|-
-! {{X20}} 2662-31G
-| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}}  || N/A || N/A ||      ||  || ||
 |-
 ! {{X22}}
@@ Line 403: / Line 436: @@
 |-
 ! {{X31}}
-| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cunk}} || {{Cyes}} || N/A || N/A ||      ||  || ||
+| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cno}} || {{Cyes}} || N/A || N/A || 0.40 || 3.02 || ||
 |-
 ! {{X32}}
@@ Line 415: / Line 448: @@
 |-
 ! {{X41_Tablet}}
-| {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cyes}}   || {{Cno|text=}} (see ref) || 0.32  || || [http://sourceforge.net/mailarchive/message.php?msg_name=4757BD30.8080808%40ugcs.caltech.edu ref] ||
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 3 || 0.40  || 75ET60WW (2.06 ) || 75HT20WW (1.02) ||
 |-
 ! {{X60}}
@@ Line 425: / Line 458: @@
 ! {{X60s}} 1704-5UG
 | {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cno|text=}} 3 || 0.34 || 7BETD2WW 2.13 || 7BHT40WW 1.13 ||
+|-
+! {{X60s}} 1704-56G
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cyes}} || {{Cunk}} || {{Cno|text=}} 3 || 0.40 || 7BETD5WW 2.16 || 7BHT40WW 1.13 ||
 |-
 ! {{X61}} 7673-CTO
-| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || 0.37 || 7NETB9WW (2.19) || {{Cunk}} ||
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes|text=}} 6 || 0.40 || 7NETB9WW (2.19) || 7MHT25WW-1.03 ||
-|-
-! {{X61}} 7675-CTO
-| {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cunk}} || {{Cyes}} || {{Cno|text=}} 6 || 0.35-test1       ||  ||  ||
 |-
 ! {{X61}} 7675-4KU
-| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 6 || 0.34 || 7NET30WW (1.11 ) || 7MHT24WW-1.02 ||
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 6 || 0.34 || 7NET30WW (1.11 ) || 7MHT24WW 1.02 ||
 |-
 ! {{X61_Tablet}}
@@ Line 440: / Line 473: @@
 ! {{X61s}}
 | {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 6 / 3 || 0.32 ||  || || [http://www.slackwiki.org/ThinkPad_X61s ref] says 3 but conflicting report received
+|-
+! {{X100e}}
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || 0.40 || 6XET36WW (1.20a) || 6XHT36WW (1.176000) || x100e NTS4UTX, dual-core L625 also works (NTT27MH)
+|-
+! {{X120e}}
+| {{Cno}} || {{Cyes}} || {{Cyes}} || {{Cno}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || 0.41 || 8FET32WW (1.16 ) || {{Cunk}} || model 0596CTO
 |-
 ! {{X200}}
-| {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 7 || 0.40 || 6DET40WW (2.04 ) || 7XHT22WW-1.04 ||
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 7 || 0.40 || 6DET40WW (2.04 ) || 7XHT22WW 1.04 ||
+|-
+! {{X200s}} 7470-X01
+| {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 5 || 0.40 || 6DET63WW (3.13) || 7XHT24WW 1.06 ||
+|-
+! {{X201}}
+| {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 6 / 5 || 0.40 ||  || ECP:  || It said 6 here, but see [http://www.thinkwiki.org/wiki/Talk:Tp_smapi#Wrong_HDAPS_axis_orientation_for_x201 discussion page]
+|-
+! {{X201s}}
+| {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cunk}} || {{Cyes}} || {{Cyes}} || {{Cno|text=}} 5 || 0.40 || 6QET44WW (1.14 ) || ECP: 1.09/1.09 ||
+|-
+! {{X220}} 4290-2GW
+| {{Cno}} || {{Cno}} || {{Cno}} || {{Cno}} || {{Cno}} || {{Cno}} || {{Cno}} || 0.40 || 8DET46WW (1.16 ) || "unknown" ||
+|-
+! {{X220}} 4286-CTO
+| {{Cno}} || {{Cyes}} || {{Cyes}} || {{Cno}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || 0.41 || 8DET54WW (1.24 ) ||  {{Cunk}} || HDAPS works fine, don't know wich axis orientation thougth ||
 |-
 ! {{X300}}
-| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || 0.37 || 7TET25WW (1.02 ) || 7THT15WW-1.00c ||
+| {{Cyes}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || {{Cyes}} || {{Cyes}} || {{Cunk}} || 0.37 || 7TET25WW (1.02 ) || 7THT15WW 1.00c ||
 |-
 ! colspan=12 style="text-align:center;background:#efefef;" |
@@ Line 507: / Line 561: @@
 * [[gkrellm-ThinkBat]] - battery status plugin for Gkrellm2
 * {{CodeRef|thinkpad-smapi.sh}} - script to display various SMAPI information using tp_smapi module.
+===See also===
+* https://wiki.archlinux.org/index.php/Tp_smapi#Workaround_for_Partially_Supported_Laptops
+== Headline text ==

Difference between revisions of "Tp smapi"

Latest revision as of 09:29, 1 May 2016

Contents

Features

Project Homepage / Availability

Installation

Installation from source

Installation in Gentoo

Installation on Debian and Ubuntu

Installation on openSUSE

Battery charge control features

Making the settings permanent on reboot

Debian

Battery status features

Scripts

Other features

Bundled hdaps driver

Troubleshooting

thinkpad_ec: cannot claim io ports 0x1600-0x161f

thinkpad_ec: no ThinkPad embedded controller!

T60p writing to start_charge_thresh/stop_charge_thresh does not work!

Model-specific status

A series

G series

R series

T series

W series

X series

Z series

SL series and IdeaPad

HDAPS axis orientation

Tools using this driver

See also

Headline text

Navigation menu

Search

Bundled `hdaps` driver

`thinkpad_ec: cannot claim io ports 0x1600-0x161f`

`thinkpad_ec: no ThinkPad embedded controller!`

`T60p writing to start_charge_thresh/stop_charge_thresh does not work!`