How to configure acpid

Introduction

Basically, acpid just executes scripts residing in /etc/acpi/actions. Which script to launch at which event is configured in several files in /etc/acpi/events.

Sources of Information

• {{{2}}} man acpid holds detailed information on how to configure acpid.
• The ibm-acpi package includes example scripts in the config folder inside the tarball. They are a good starting point to adjust them to your needs.
• You also might want to have a look at the ACPI section of the Configs page or the Scripts repository.
• And you can find information about the event strings ibm-acpi generates for certain keys at the Special Keys HOWTO.

Example: go to sleep on lid close

To make the ThinkPad go to sleep when you close the lid, you need to add an event handler for the lid event and an action script that takes care of going to sleep and resuming.

Event Script

The event script needs to be created within /etc/acpi/events and can have any name you like. In this case we call it lid because it will trigger the lid event. Do # vi /etc/acpi/events/lid and make it look like this:

event=button/lid
action=/etc/acpi/actions/sleep.sh %e

The "event" line is a regular expression specifying the events we're interested in. You can determine what the event strings are from looking at /var/log/acpid after trying to suspend, close the lid, etc. . You can find information about the event strings ibm-acpi generates for certain keys at the Special Keys HOWTO.

The "action" line is the command to be executed when these events are dispatched. In this example we call the sleep.sh script residing in /etc/acpi/actions and pass the event description text using the %e placeholder.

NOTE!

To make your changes take effect after adding or modifying the events files you must do a kill -SIGHUP `pidof acpid`

.

Action Script

Our example /etc/acpi/actions/sleep.sh script looks as follows:

#!/bin/sh

# if launched through a lid event and lid is open, do nothing
echo "$1" | grep "button/lid" && grep -q open /proc/acpi/button/lid/LID/state && exit 0

# remove USB 1.1 driver
rmmod uhci_hcd
 
# sync filesystem and clock
sync
/sbin/hwclock --systohc

# switch to console
FGCONSOLE=`fgconsole`
chvt 6
/usr/sbin/radeontool light off

# go to sleep
echo -n "mem" > /sys/power/state

# readjust the clock (it might be off a bit after suspend)
/sbin/hwclock --adjust
/sbin/hwclock --hctosys

# reload USB 1.1 driver
modprobe uhci_hcd

# turn on the backlight and switch back to X
radeontool light on
chvt $FGCONSOLE

Explanations

• The lid generates an event for both opening and closing thus requiring that we check it's state and only act if it's closed.
• There have been problems encountered with the USB devices not working properly after a resume from suspend. To circumvent those we remove the USB driver prior to suspend and reload it afterwards.
• Note that the # echo -n "mem" > /sys/power/state line does not return until we are revived. So there is only one event generated and there is no need to check the state of anything.
• The console switching code in this script is a special solution for a problem where the backlight doesn't switch off on the T30 and some other models. Before going to sleep, these models switch to console mode which causes the backlight to come back on. So we preemptively switch to console mode and turn off the backlight using radeontool before going to sleep.

NOTE!

If your display doesn't come back on resume, look here.

Troubleshooting

• If something doesn't work, your first action should be a # tail /var/log/acpid. It will tell you a lot about what is going on. If it has "Permission denied" errors, check the permissions of your /etc/acpi/actions scripts (especially make sure that the executable bit is set). Also check the permissions for other involved files like i.e. device nodes.