Madwifi

Madwifi (Multiband Atheros Driver for Wifi) is Linux driver for 802.11a/b/g universal NIC cards - Cardbus, PCI, or miniPCI - using Atheros chip sets.

The following (incomplete) list of adapters sold by IBM use the Atheros chips:

• IBM Dual-Band 11a/b Wi-Fi Wireless Mini PCI Adapter
• IBM 11b/g Wireless LAN Mini PCI Adapter
• IBM 11a/b/g Wireless LAN Mini PCI Adapter
• IBM 11a/b/g Wireless LAN Mini PCI Adapter II
• ThinkPad 11a/b/g Wireless LAN Mini Express Adapter
• IBM 802.11a Wireless LAN Cardbus Adapter
• IBM 11 a/b/g Wireless Cardbus Adapter

• (11a/b/g/n) Atheros Communications, Inc. Unknown device 0024 (rev 01) (using SVN revision 2360+)

Packages

• Official Debian packages in the non-free section. See also the Alioth project page and the Madwifi wiki.
• Debian Packages: http://www.marlow.dk/madwifi
• Debian Packages: http://www.users.tpg.com.au/sigm/debian/pkg-madwifi/
• Fedora Packages(1): http://rpm.livna.org
• Fedora Packages(2): http://www.atrpms.net/name/madwifi/
• Gentoo ebuild: $ emerge net-wireless/madwifi-driver net-wireless/madwifi-tools
• SUSE Packages http://madwifi-project.org/wiki/UserDocs/Distro/SuSE
• Ubuntu Package: $ sudo apt-get install linux-restricted-modules-`uname -r`
• MadWifi packages and source for these and other distributions

Source

Detailed instructions can be found on the MadWiFi Wiki.

• Daily Snapshots
• checkout from svn:

$ svn checkout svn.madwifi-project.org/madwifi/trunk madwifi

Installation

• Make sure that you've got sysctl support and the net/radio enabled (wireless extensions) in your kernel. Install the driver with make & make install
• further more you like to install the wireless tools from wireless tools. Make sure the versions fit together by

$ iwconfig --version

Setting up wpa_supplicant with wpa-psk.

You can enable the wireless LAN status LED on your Thinkpad by following these instructions (tested on Thinkpad x60s).

Status

Release 0.9.4[1] available

Release notes

   * fixes compilation for recently released kernel 2.6.24
   * introduces Minstrel rate control algorithm
   * introduces switch to turn ANI (Ambience Noise Immunity) off, which can help to improve performance (see also #705)
   * several bug fixes to improve stability
   * now defaults to radiotap headers in monitor mode
   * adds support for variable number of VAPs, tunable via module parameter

Free Software HAL

The old madwifi driver consisted of a BSD/GPL wrapper with an unmodifiable HAL (Hardware Abstraction Layer). This HAL was not binary firmware as with the Intel wireless chips, but a piece of code that needed to run in the Linux kernel. It consisted of header files for which no permission to modify was granted, and pre-compiled object files. The vendor's position was that the Linux community simply needs to accept this sourceless HAL, since in principle the Atheros chip could be tuned to any frequency, and thus produce RF interference with systems operating in those frequencies.

This binary HAL was unacceptable to the Linux kernel developers, and the Atheros driver in this state would never have become a part of the official kernel. Some OpenBSD developers, facing the same issue, clean-room reverse-engineered the binary HAL and had produced an open source driver (ath5k), which was subsequently picked up by the madwifi team as the future direction. At the same time the old madwifi driver was labeled 'legacy' to reinforce this point.

In the meantime the ath5k driver has been merged into the linux kernel, and Atheros has come around and hired a linux kernel developer, released a second driver (ath9k) for newer wireless chips and has taken over maintenance of the ath5k driver.

As of the latest distributions (Ubuntu 8.10 and Fedora 10) the atk5k driver is still flaky, but those problems seem to be resolved with the latest mainline kernel (2.6.29).

NOTE!

{{{1}}}

Problems on Fedora 9

When installing madwifi 0.9.4 on my new machine (from source), ath_pci would load fine, apparently, but I could only see the wlan0 interface via iwconfig, and no attempt to create an ath0 interface or start it (via ifconfig) would work. I finally found the problem (described in this email trail) which indicates the new ath5k module is the problem.

As directed, I fixed it by editing /etc/modprobe.d and creating a file called madwifi with the following in it:

alias wlan0 ath_pci
blacklist ath5k

Although this enables ath0, I have yet to get the wirelss to actually connect to anything.

External links

• Official website