Installing Ubuntu 7.10 (Gutsy Gibbon) Tribe 3 on a ThinkPad T61

From ThinkWiki
Revision as of 20:03, 25 July 2007 by Wehe (Talk | contribs) (added references section and link to TuxMobil)
Jump to: navigation, search

Opening Notes:

1) This is written for Tribe 3, as development moves forward many of the items listed here will (hopefully) no longer be necessary or no longer apply.

2) Use the Alternative Installer, the Desktop installer installs but fails to boot

3) While Gutsy has been relatively stable lately if you are looking for stability stay with Feisty.

Hard Disk Controller

When the system boots hit F1 to enter the Bios, select Config->Serial ATA (SATA) and set the SATA Controller mode option to "Compatibility".



Must install using the alternate CD or the regular CD and hit F4 to change VGA settings to 1024x768x32 and use regular install.

Starting with Tribe 3 on the T61, Ubuntu defaults to using the Intel driver.


As of July 10th the latest nv 2D driver was released that supports the 140m in the T61 and this driver is in Tribe3.

If you would like 3D acceleration then you must download and install the proprietary drivers from Nvidia here:

To install these drivers:

1) install build-essentials from Synaptic

2) Download the drivers from the link above to your home directory

3) When the download completes hit Ctrl-ALT-F1 to drop to a console.

4) Login and type:

# sudo /etc/init.d/gdm stop

# sudo sh

If the file you download is newer that 100.14.11 make sure you modify the command appropriately

When asked permit the installer to modify your xorg.conf

Reboot: # sudo shutdown -r now

With each new Kernel release this process must be repeated except you should tell the installer to not update xorg.conf


The Atheros card should be supported by the drivers built into Gutsy.

Help needed
Can someone with an Atheros card confirm this?

The Intel a/b/g/n (IPW4965) card requires the iwlwifi drivers from Intel:

As the release process moves forward the Kernel will be updated so make sure to update the paths below
With each new Kernel release this process must be repeated

Install the necessary prerequisites and get the directories symlinked right.

sudo apt-get install build-essential linux-headers-`uname -r`
sudo ln -s /usr/src/linux-headers-`uname -r` /lib/modules/`uname -r`/source

Download and install the latest mac80211 from the 8.x.x branch. 8.0.2 is the latest as of this edit. The 9.x.x branch is currently experimental.

tar -xzf mac80211-8.0.2.tgz
cd mac80211-8.0.2/
sudo make patch_kernel
cd ..

Download and install the latest iwlwifi from the 0.0.x branch. 0.0.42 is the latest as of this edit. The 0.1.x branch is currently experimental, but is necessary if you need to use 802.11n. These instructions may or may not work if you want to use 0.1.x.

tar -xzf iwlwifi-0.0.42.tgz
cd iwlwifi-0.0.42/
sudo make install
cd ..

Download and install the latest 4965 ucode.

tar -xzf iwlwifi-4965-ucode-4.44.17.tgz
cd iwlwifi-4965-ucode-4.44.17/
sudo cp iwlwifi-4965.ucode /lib/firmware/`uname -r`

Make sure the hardware wifi switch is on before doing this.

sudo modprobe iwl4965

After that, you should simply be able to connect to wireless networks using Gnome's network manager.


Audio does not work out of the box, download and install the latest version of Alsa from CVS using the instructions here: