Installing Fedora 14 on a ThinkPad T41

From ThinkWiki
Revision as of 13:19, 1 March 2011 by Tonko (Talk | contribs) (Kernel)
Jump to: navigation, search
NOTE!
This is based on Fedora 14 with the default GNOME desktop. Your experience with KDE may be different.
Help needed
Not all models of this ThinkPad are equal, you may have a different WiFi adapter, or some options I did not have. If you tested them, please add their status down below.

New in this release

Fixed or new in this Fedora release, with regards to this model ThinkPad is the following;

  • External ONLY display now works when using Fn-F7 (Previously caused both displays to switch off)
  • tpb is no longer part of Fedora, so no OSD any more for volume and brightness keys

Success Chart - Out of the box experience

This machines SMOLT profile is available here.

Item Working Notes
Installation Local CD/DVD install yes
Network Installation yes
USB Installation unknown
Display - ATI RV250 Laptop Screen yes
VGA yes
DVI yes Requires port-replicator or dock with DVI
S-Video partial see below
Power Management Software Suspend (hibernate) yes
Suspend to Memory (ACPI sleep) no Xserver hang on resume. bugzilla. Boot with radeon.agpmode=1 as a workaround.
Audio yes
Wireless WiFi - Atheros AR5212 yes
WiFi - Intel unknown (should work)
Bluetooth yes
Input Keyboard yes
TrackPoint yes Install gpointing-device-settings rpm for full configuration capabilities
TouchPad yes Install gpointing-device-settings rpm for full configuration capabilities
Extra keys partial see ThinkPad Extra keys section below
Ports Ethernet yes
Modem no Requires closed-source driver. Install the slmodem rpm from the rpmfusion-nonfree repository, edit /etc/sysconfig/slmodem and set INTERFACE=alsa and ALSA_DEVICE=modem:1 and optionally the country. Then run "chkconfig slmodem on; service slmodem start" and point your dialer to /dev/ttySL0
Serial yes Requires port-replicator or dock
IrDA no Device is detected, but does not work
PS/2 Keyboard/Mouse yes Mouse works, but disables Trackpoint/Touchpad
Parallel unknown (should work) Device is detected
USB yes
PCMCIA/Cardbus yes
Harddisk Active Protection no Fedora ships the hdapsd rpm, but not the tp_smapi kernel module, which is required to read the motion sensor bugzilla
Ultrabay device removal partial Eject switch causes udev event, but no default udev script to handle the event to unmount filesystems in time. ata_piix does handle the removal and insertion of ATA devices.
TPM (security subsystem) yes Enable security chip in BIOS, then "yum install tpm-tools", then "modprobe tpm_atmel; service tcsd start; tpm_version" works.
Dock removal unknown

Tested and Verified on Fedora 14

Information in this section has been tested and verified using this Fedora release.

Installation

Installation is straight forward, you can follow the generic Fedora install instructions.

Configuration

Kernel

It is recommended to edit /boot/grub/grub.conf and add hpet=force to the kernel line. This will activate HPET (High Precision Event Timer), which will allow the CPU to sleep for longer periods and save power.

You will also want to add radeon.agpmode=1 to work around a suspend/resume bug by forcing AGP 1X mode. Do note that forcing AGP 1x mode will mean less performance in games that copy large sets of textures around (e.g. Quake, World of Padman).

X Server - ATI RV250

Out of the box external displays (VGA or DVI) should work, and you can switch display modes with the Fn-F7 key combination.

The following issues still exist for single-head (LVDS only) setups

  • unknown physical LVDS display size (0mm x 0mm) reported by RandR

And for Multihead or External displays. Some of these issues are likely caused by the limited amount of VRAM available (32MB)

  • S-Video output is distorted Bugzilla
  • Multihead causes the desktop to become very slow
  • Screen rotation does not work in combination with Multihead
  • Compiz does not work in combination with Multihead Bugzilla
  • Metacity Compositing does not work with Multihead
  • Strangely enough, plymouth gives a high-res text mode during boot with single-head, but graphical mode with Multihead boot

WiFi

Both the Intel and Atheros AR5212 wireless should work out of the box.

Intel WiFi was not tested.

ThinkPad Extra keys

ThinkPad keys are handled by a mixture of the thinkpad_acpi, acpi button and acpi dock drivers.

Key Function Handled by Event Works Notes
FnF3 lock screen thinkpad_acpi HAL yes
FnF4 suspend acpi button HAL partial button works, but suspend fails on resume
FnF5 wireless thinkpad_acpi HAL partial Works as a radio kill switch, kills WiFi but not Bluetooth
FnF7 videomode thinkpad_acpi HAL yes
FnF12 hibernate acpi button HAL yes
FnHome brightness up - no yes no OSD
FnEnd brightness down - no yes no OSD
FnPgUp thinklight - no yes no OSD
FnSpace zoom thinkpad_acpi HAL no Known Xorg limitation, scheduled to be fixed with the new XKB2 extension, whenever that may be.
VolumeUp Volume Up thinkpad_acpi no yes no OSD. Hardware and Software volume controls are independent from each other.
VolumeDown Volume Down thinkpad_acpi no yes no OSD. Hardware and Software volume controls are independent from each other.
Mute Mute thinkpad_acpi no yes no OSD. Hardware and Software mute controls are independent from each other.
Access IBM Vendor key thinkpad_acpi HAL partial No default action, but can be associated with gnome-keybinding-properties
NextTab Browser Next tab standard keyboard driver HAL yes
PreviousTab Browser Previous tab standard keyboard driver HAL yes
Power Power button acpi button HAL yes Need to press button for ~1 second to trigger event. Causes a dialog asking you what to do.
Lid Lid button acpi button HAL yes
Dock Dock eject button acpi dock unknown unknown Should cause udev event
Ultrabay Ultrabay eject switch acpi dock udev no Causes udev event, but missing handler. See below.

Ultrabay

Ultrabay eject is not handled properly by default. Since there is no undock udev handler. This udev rule and eject script works for me: How to hotswap Ultrabay devices

IrDA

IrDA is detected, but does not work. Part of the problem is that the default Fedora configuration expects to find the IrDA port at /dev/ttyS2, while it should use /dev/ircomm0 instead. This can be fixed in /etc/sysconfig/irda after which the irda service can be started (# systemctl start irda.service).

However, even after this communication with other devices fails. irdadump does not show any output when something like a mobile phone with IrDA is sending data.

Untested on Fedora 14

The following features where not tested with this Fedora release. If you have tested them, please update the table

  • Intel WiFi
  • Parallel port
  • Dock eject