How to make use of Dynamic Frequency Scaling

From ThinkWiki
Revision as of 04:27, 1 August 2005 by Evan.heidtmann (Talk | contribs) (→‎Using the Sys Interface)
Jump to: navigation, search

General

Linux supports Dynamic Frequency Scaling for ThinkPads with mobile Pentium III, Pentium 4 and Pentium M processors.

Debian notes

Instead of compiling your own kernel, you can use the Debian "stock" kernel. In Unstable/SID the 2.6.12 kernel image with an /etc/modules that include: 

battery
ac
thermal
processor
acpi-cpufreq
cpufreq-userspace

With the powernowd package and you should be setup.

Configuring the Kernel

2.4 Kernels

There were various frequency scaling implementations in the 2.4 series of kernels. They all were preliminary and a standard was rised with the introduction of the sysfs filesystem in 2.6 kernels. It is recommended to use a 2.6 kernel, if possible.

2.6 Kernels

You need to enable the cpu frequency scaling for your kernel (usually your distros kernel will have this enabled): 

CONFIG_CPU_FREQ=y

You need to enable governors, if not already done in your distros default kernel: 

CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
CONFIG_CPU_FREQ_GOV_POWERSAVE=y
CONFIG_CPU_FREQ_GOV_USERSPACE=y

Since 2.6.10 there is the ondemand governor that does cpu frequency scaling in kernel so you dont need userspace programs like powernowd etc. It can be enabled with: 

CONFIG_CPU_FREQ_GOV_ONDEMAND=y

Using the Sys Interface

The files in /sys/devices/system/cpu/cpu0/cpufreq/ provide information and a means of controlling the frequency scaling subsystem. Seed values are given in Khz. You need to be root to access the /sys filesystem.

Your max speed is at /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq.

# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_max_freq
700000

Your min speed is at /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_min_freq.

# cat /sys/devices/system/cpu/cpu0/cpufreq/cpuinfo_min_freq
500000

If you are using the userspace governor, you can write to /sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed to change the current speed.

# echo 700000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed
# cat /proc/cpuinfo
cpu MHz  : 697.252
# echo 900000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed
# cat /proc/cpuinfo
cpu MHz  : 976.152

Using Frequency Scaling Governors

You can compile the scaling gouvernours into your kernel or compile it as module. You'll find the gouvernors with 'make menuconfig' here:

Power managemant options (ACPI, APM) --->
CPU Frequency scaling --->

After booting the new kernel you can get a list of available governors with (as root):

# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_governors
conservative ondemand powersave userspace performance

A Short Overview over the available governors:

ondemand
This driver is a dynamic cpufreq policy governor. It changes frequency based on the processor load.
conservative
New since 2.6.12. Similar to ondemand. Optimized for battery powered environments and AMD64.
powersave
Like the name says, your battery would choose this one ;). It sets the Frequency always to the lowest available.
userspace
You have to choose this one, if a frequency scaling daemon should manage your CPU frequency or you want to do it manually.
performance
This governor sets your Frequency always to the highest available.

Now we set our governor: What is our current governor?

# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
userspace

Set new governor and watch if it has changed

# echo conservative > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
conservative

Congrats! Your governor is active.

You may set the governor in your rc.local, to make it used on every boot.

Debian has no rc.local, so read this and this

Using Frequency Scaling Daemons

NOTE!
It is recommended to use the ondemand frequency scaling governor, available in kernels from 2.6.10. See above. If you do this you do not need a frequency scaling daemon

Don't forget to enable the userspace governor to have a userspace daemon do the frequency scaling. If it is built as module, load it as cpufreq-userspace.

There are plenty of userspace frequency scaling daemons available:

Troubleshooting

  • If you have a Coppermine-piix-smi based Thinkpads like from the A2x, X2x and T2x series you need to enable the speedstep-ich driver in the kernel and load it if it's built as module. You might want to look at this page.
  • If you have a p4-class celeron based Thinkpad like the R40e you might want to look at this page
Retrieved from "https://www.thinkwiki.org/w/index.php?title=How_to_make_use_of_Dynamic_Frequency_Scaling&oldid=8045"