Installing Debian 7.0 (Wheezy) on a ThinkPad Edge E135
This is a short guide to installing Debian 7.0 (wheezy, currently testing, installer beta 4) on a ThinkPad Edge E135.
It is sufficient to get the base system running; several subsystems have not yet been tested. As wheezy is not released yet, some steps might not be necessary in the future any more.
Contents
Installation
Debian can be installed from a USB device (the E135 does not have an optical drive). The installer asks for firmware for the ethernet and wifi interfaces; those requests can safely be ignored. Wired ethernet will work without the firmware as well (but seems limited to 100mbps). If a firmware-brcm80211 package is provided on an additional USB stick, the module can be loaded and wifi can be used.
Graphics
When the installer has completed and the system reboots, interrupt the bootloader by pressing `c` and write the following commands:
> insmod efi_gop > insmod efi_uga > insmod gfxterm > set gfxmode=auto > set gfxpayload=keep > terminal_output gfxterm
Then press Escape, `e` and add these parameters to the `linux` line:
radeon.modeset=0 1
Log in using your root password, download all the .bin files from [1] into /lib/firmware/radeon, and install libdrm2 and libdrm-radeon1 from the experimental repositories (>=2.4.40). That can be accomplished by those commands, assuming you are connected to a typical wired network:
# dhclient eth0 # mkdir /lib/firmware/radeon # cd !$ # wget -m -l1 http://people.freedesktop.org/~agd5f/radeon_ucode/ # mv people*/*/*/*.bin . # echo "deb http://cdn.debian.net/debian/ experimental main" > /etc/apt/sources.list.d/experimental.list # sed "s/^deb cdrom/# &/" -i /etc/apt/sources.list # apt-get update # apt-get -t experimental install libdrm2 libdrm-radeon1 # reboot
Since GDM and Gnome seem to have issues with the graphics system provided by this setup, that would also be a good time to install xdm and xfce4.
After rebooting, you should be able to log in graphically.
Open issues
- Starting Gnome makes the X server crash for yet-to-be-explored reasons.
- Try the whole setup process with more than an empty standard software selection. (Might interfere with display setup as long the drivers are not installed yet.)
- The GRUB `insmod` lines are not necessary under all conditions. Especially, when an unencrypted disk is used, they seem to be optional; has to do with the early initial password prompt.
- Device doesn't come up after suspend
Hardware status
(none thereof tested in detail, eg if they operate at nominal speeds)
- Webcam: works
- Card reader: works with SD cards (no others tested)
- Touch pad, track point: work
- wifi: works
- Ethernet: works
- Regular USB: works
- Untested:
- USB 3
- Video connection
- Audio jack
- Bluetooth
Tweaks required
Volume keys
Multiple ALSA cards are detected, confusing xfce4-volumed. (In other words, volume buttons don't work). Can be fixed by installing gstreamer0.10-pulseaudio, and possibly setting the pulse audio sound card in the XFCE4 settings. Reported.
WiFi
The wifi card is soft blocked at bootup (meaning that the OS thinks that something in the hardware is suggesting that wifi better be off). It can be explicitly unblocked with the rfkill utility, but in practice, installing the urfkill package is recommended, which makes the toggle-wifi (Fn-F9) hardware button work.
network-manager seems to be able to unlock cards too.
After the original installation, the WiFi only worked a few meters from the base station, as if a power saving mode that should be was active. That went away after some updates; a system from wheezy as of 2012-11-29 should work.
