How to install the development version of atk9k

From ThinkWiki
Revision as of 20:53, 13 August 2008 by Kevmitch (Talk | contribs) (→‎Compilation)
Jump to: navigation, search

ath9k is the new open source driver for newer atheros cards including those with 11n hardware support.

At the time of writing(Kevmitch 21:21, 13 August 2008 (CEST)), ath9k will not compile against the current kernel release 2.6.26. It is however included in the most recent release candidate 2.6.27-rc3. Thus, in order to get it running, you will either need to backport ath9k to your older kernel or download and compile 2.6.27-rc3. It is expected that the latter process will be significantly easier especially now that you can download the necessary kernel source directly off the web without using git. If you have managed to backport the driver to an older kernel, please share your knowledge and add to this page.

Preparation

Compiling your kernel is at a minimum going to require gcc, make and the qt3 development libraries to run the x-configuration utility. The names of these packages and how to install them will vary from distro to distro. You'll also want to add yourself to the src group so that you can do most of the kernel compilation as a regular user. You will have to log out and log back in for this change to take effect.

Debian

# aptitude install git-core build-essential kernel-package libqt3-mt-dev fakeroot # adduser <you> src

Ubuntu

$ sudo aptitude install git-core build-essential kernel-package libqt3-mt-dev fakeroot # sudo adduser <you> src

Get the kernel sources

Download and unzip the kernel sources

$ cd /usr/src
$ wget http://www.kernel.org/pub/linux/kernel/v2.6/testing/linux-2.6.27-rc3.tar.bz2
$ tar xvjf linux-2.6.27-rc3.tar.bz2
$ cd linux-2.6.27-rc3

Kernel config

This is the part most people are afraid of. However, you can use your current kernel's configuration as a baseline to help ease the pain. Most self-respecting distributions keep a copy of your kernel configuration in the /boot directory alongside the kernel itself. If this is not the case, you might find a copy of the kernel config at /proc/config.gz (which will of course needs to be gunziped). Whatever the case, you will want to copy the the current config file to /usr/src/wireless-testing/.config

Debian

$ cp /boot/config-`uname -r` /usr/src/wireless-testing/.config Does this work on Ubuntu?

Configure the kernel

Now run

$ make xconfig

You'll likely see some messages in the terminal about unset or unrecognized configuration variables which should be automatically either added or removed respectively. You might want to make sure the following are enabled

Networking → Networking Options → [Y]QoS and/or fair queueing (CONFIG_NET_SCHED)
Networking → Networking Options → QoS and/or fair queueing → [M]Multiband Priority Queueing (PRIO) (CONFIG_NET_SCH_PRIO)
Networking → Wireless Networking → [M]Improved wireless configuration API (CONFIG_CFG80211)
Networking → Wireless Networking → Improved wireless configuration API → [Y]nl80211 new netlink interface support (CONFIG_NL80211)
Networking → Wireless Networking → [Y]Wireless Extensions (CONFIG_MAC80211)
Networking → Wireless Networking → [M]Generic IEEE 802.11 Networking Stack (mac80211) (CONFIG_WIRELESS_EXT)
Networking → Wireless Networking → Generic IEEE 802.11 Networking Stack (mac80211) → Rate control algorithm selection → [Y]PID controller based rate control algorithm (CONFIG_MAC80211_RC_PID)

and most importantly

Device Drivers → [Y]Network Device Support (CONFIG_WLAN80211)
Device Drivers → Network Device Support → Wireless LAN → [Y]Wireless LAN (IEEE 802.11) (CONFIG_WLAN80211)
Device Drivers → Network Device Support → Wireless LAN → Wireless LAN (IEEE 802.11) → [m]Atheros 802.11n wireless cards support (CONFIG_ATH9K)

Also, unless you want to worry about creating an initrd (initial RAM disk), you're also probably best to build anything necessary to read your root filesystem into the kernel rather than as modules. This includes both filesystem (e.g. ext3) and low level hardware drivers (e.g.libata). The particular drivers required will depend on your particular setup.

Make sure you save any changes you make before you exit.

Compilation

Now it's time to compile your kernel. The generic way to do this is

$ make
$ su
# make modules_install
# cp arch/<your architecture>/boot/bzImage /boot/linux-2.6.27-rc3

Where <your architecture> will be x86 if you're running a 32-bit system or x86_64 if you're running 64-bit.

Then you'll have to set your bootloader to load the new kernel. If you're using grub, you'll add this to /boot/grub/menu.list or /etc/grub.conf or whatever 

title	        Wireless testing Linux kernel 2.6.27-rc3
root		(hd#,#)
kernel		/boot/linux-2.6.27-rc3 root=/dev/<your root device> ro

You're going to have to set (hd#,#) and root=/dev/<your root device> to reflect your boot device configuration. The best bet is probably to just copy and modify an existing entry.

NOTE!
If you compiled the drivers needed to access your root device (filesystem and hardware driver) as modules rather than building them directly into the kernel, you're going to have build an initrd, using something like mkinitramfs and add the resulting initrd to the above grub stanza as follows:

initrd /boot/initrd.img-2.6.27-rc3

Now reboot into your new kernel.

Debian

Debian has a system to help you build kernels as Debian packages.

$ fakeroot make-kpkg --append-to-version=.mykernel linux_image
$ su
# dpkg -i /usr/src/linux-image-2.6.27-rc3.mykernel_2.6.27-rc3.mykernel-10.00.Custom_amd64.deb
or if you're running 32-bit i386 # dpkg -i /usr/src/linux-image-2.6.27-rc3.mykernel_2.6.27-rc3.mykernel-10.00.Custom_i386.deb

which should take care of all of the above for you with the possible exception of the initrd. Again it is recommended that you build what you need into your kernel.

Ok, now see if it worked

Once you have your kernel compiled and install, reboot and choose it from your grub or lilo menu. Hopefully it boots Ok, and you can open a command line and # modprobe ath9k
# iwconfig
The first command should hopefully generate no errors and the second is purely diagnostic and should show you a working wireless device. You can then proceed to use wpa_supplicant or network manager or iwconfig to setup your wireless networking.

Keeping up to date

If you want to keep up to date with the latest developments, you can always check the git tree of the wireless-testing kernel for code changes.

$ cd /usr/src/wireless-testing && git-pull

Of course you will have to repeat the necessary steps above to recompile and reinstall any changes.

Retrieved from "https://www.thinkwiki.org/w/index.php?title=How_to_install_the_development_version_of_atk9k&oldid=38552"