Installing openSUSE 10.3 GM on a ThinkPad T61
Here are my specs on my thinkpad t61
2.0GHz 4meg cache core 2 duo
2 gigs of ram
nvidia nv140 128 megs of ram
14.1 inch 1440x900 display
atheros a/b/g wireless card
Think finger
100 GB 7200 RPM hard drive
There are other configurations out there, so hopefully people with the different parts can do their part and chip with how they got their to work.
Contents
Video
Thinkpads have an option for either an nv140 or an Intel card. I only have the nvidia option, so someone else can add the Intel card.
Nvidia There are multiple ways to do it, but I am going to do the old fashioned way from nvidia, while it may be a little harder, you can do it with any driver.
1. Download the linux x86_64 driver from http://www.nvidia.com, note where you download it to. Also ensure that you installed "Linux kernel development" under yast, software.
2. once done, open a terminal console with a "ctrl- alt - f2"
3. login as root
4. execute the command init 3
5. After it is done (a few seconds later), hit enter once
6. cd to where you downloaded the file (by default /home/$USERNAME/Desktop where $USERNAME is the user WHO DOWNLOADED THE FILE)
7. executesh NVIDIA-Linux-x86_64-100.14.19-pkg2.run
8. Answer a bunch of questions, at the end answer yes to setting up you xorg.conf file.
9. Run a init 6 to reboot
---
All these steps are not required if you have T61 with Intel graphics card (as I do), in this case everything works just fine out of the box.
Wireless
To my knowledge this laptop comes with an option for 3 different wireless network cards. Here are my instructions for the atheros, I am hoping someone else can write the instructions for everything else.
Atheros: 1.Go to madwifi's home page (using the wired Ethernet will work, or you can use another machine) http://madwifi.org/. From this website you can download the driver.
2. Open up the command line (konsole) and "Untar" the file with a tar xvf madwifi-0.9.3.2.tar.gz
3. Switch to the root user with su then change into the directory with a cd madwifi-0.9.3.2
4. compile the driver and load the module (it is really easy, I promise) with a make ; make install; modprobe ath_pci. You should get a bunch of jibberish on your screen and a few minutes later it will be done.
4. Open up yast by hitting "alt-f2" and typing in "yast".
5. Go to network devices -> Network card -> add
6. Select the device type to wireless
7. add to the module name ath_pci and hit next.
8. configure it for your network
9. Once you reboot you should be good to go.
---
My T61 comes with "Intel Corporation PRO/Wireless 3945ABG" wifi controller, which worked out of the box without installing any additional drivers (yeah, I did not forgot to insteall iwlwifi and iwl3945 packages during the installation).
Sound
Sound works out of the box, it is just set up a little funky. In KDE if you go to the speaker icon and click on it, then go to "mixer" to get to the settings. Here you will raise the volume on "PCM". Then go to the tab "switches" and ensure that speaker is turned on. Once you are done right click on the speaker icon again and go to "select master control". Select "PCM" and hit ok. Your buttons will now to raise and lower the volume. Mute does nothing though.
---
Don't forget to raise volume levels in alsamixer, they are muted by default! Everything else is works as expected (mute button mutes, volume up button raises volume and volume down vice versa).
Display
1440x900 working great. Selected 16:10 aspect ratio when installing and then the resolution and it is working fine. The brightness adjuster doesn't work in X.org. You need to switch to a console (ctrl - alt - f2) to lower the brightness, then switch back (ctrl - alt - f7). Hopefully someone gets this working! I am pretty sure it is an issue with the nvidia driver, but I can't be for sure.
---
No idea about NVidia (I intentionally decided to buy a machine without it, since I'm tired of bugs in their binary-only drivers), but kpowersave is able to change the brightness here. You can do the same using /proc/acpi/ibm/brightness (see `cat /proc/acpi/ibm/brightness`).
Bluetooth
Works like a champ, I set up a wireless mouse with it using KDE, no problem.
---
Bluetooth freezes my machine after waking up from suspend-to-ram (making it almost impossible to debug). I don't use any bluetooth devices, so I have just disabled it by `echo "disable" > /proc/acpi/ibm/bluetooth`.
Think finger
Coolest feature of this laptop, of course we need to get it working.
1. Go to yast (alt-f2 and type in yast) then "hardware" -> "Fingerprint Reader". Just simply enable it and then hit finish. Yast will install a few packages and you are ready to set it up.
2. From the console execute tf-tool --add-user $USERNAME where username is your username.
3. Swipe your finger successfully three times and you are done, to login type in your username and then swipe your finger.
---
Yes, it works fine in console, though neither kdm, nor gdm support it, which makes this thing pretty much useless. The only advantage is that you don't need to type root password when doing 'su -'.
Suspend and Suspend to Disk
Not working so well, hit suspend and it does nothing. Suspend to disk works, and then won't successfully wake up.
---
Works like a charm here, both to ram and to disk. Checkout kpowersave settings and make sure you have this line: S2RAM_OPTS="-f -a3" in /etc/pm/config.d/defaults (-f is needed because T61 is quite new and not yet listed in s2ram database).
Also working here with the S2RAM_OPTS set properly as above.
