Installing Debian Sid (October 2005) on a ThinkPad T42

Debian netinst

Insert the Debian net installation disk (download size ~130 MB) and on bootup, the laptop should go directly to the Debian splash image prompting you for a boot parameter. If you don't see this screen, then you possibly need to change the boot device configuration in your BIOS and make the CD drive the first boot disk.

Enter expert26 to start the installation with Kernel 2.6, and it will take you through the regular Debian setup which contrary to published reports on Slashdot and SuSe forums is very intuitive and non-scary. Everything I had on this machine (lspci output below) was detected with the sole exception of the Intel Pro Wireless 2200 wireless card. It turned out later that getting wirless to work was really easy in debian.

Debian should install just fine and on first bootup, install the packages you want. X should just work with all the auto-detect options in the installer. I have a SXGA monitor and the display worked correctly from the first go. The only problem I had with the Debian installer is that at the time of my install, gnome was in transition so I couldn't immediately install the mail client of choice -> Evolution.

My configuration

Here is the lspci output from my system, a more non-cryptic description of my config is below

0000:00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)

0000:00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03)

0000:00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)

0000:00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)

0000:00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)

0000:00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)

0000:00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)

0000:00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)

0000:00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01)

0000:00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)

0000:00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)

0000:00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01)

0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500]

0000:02:00.0 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev 01)

0000:02:00.1 CardBus bridge: Texas Instruments PCI4520 PC card Cardbus Controller (rev 01)

0000:02:01.0 Ethernet controller: Intel Corporation 82540EP Gigabit Ethernet Controller (Mobile) (rev 03)

0000:02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG (rev 05)

In summary,

Intel 1.73 Pentium M (Dothan)

Intel Pro Wirless 2200

SXGA monitor (14", 1400x1050)

512 MB of RAM

Intel Gigabit Ethernet

IBM Security System

Integrated fingerprint reader

56 K modem

Getting wirless to work

I had a Sony Vaio for a few months and I had to go through hell to get wirless to work on that one. The reason for that primarily was that it was an old machine and wirless access was through the PCMCIA port. However, Vaios are notorius for not passing their IRQ requests correctly, and so Linux was never able to asign the PCMCIA bus a correct IRQ channel and the PCMCIA devices never worked. I had to make do with a USB ethernet driver and it wasn't as fast, and stuck out from the back and looked very ugly.

I'm happy to report that nothing like that occurred in my Thinkpad T42.

To get wirless to work on your Debian box, do the following

$ apt-get install wireless-tools ipw2200-source ieee80211-source

in addition to this make sure you apt-get your kernel-source (linux-source as of 2.6.12), linux-headers, and linux-tree packages.

Once you have this navigate to /usr/src where all these packages are installed and bunzip/tar them so that a linux-source directory is created, and also a modules directory is created which has the ipw200, and ieee80211 sources.

Now, make a symlink called linux to your linux-sources directory

$ ln -s linux-sources-2.6.x.y linux

make sure it works by typing in ls -l in /usr/src and see that linux points to your linux-sources directory

To get the ipw2200 wireless utilities to work, you need to download the correct firmware from intel.com The ipw2200 sourceforge page at IPW-Sourceforge will have directions for you. Make sure you download the correct version that corresponds to your ipw2200-source. You can check your ipw2200-source version by going

$ dpkg --info ipw2200-source

Now that you've downloaded and installed the firmware files in /usr/lib/hotplug/firmware/ you need to build your ipw and ieee80211 sources

You can do it by typing in these commands in /usr/src

$ module-assistant a-i ieee80211

$ module-assistant a-i ipw2200

This will create 2 .deb files in your /usr/src directory. If debian doesn't install them automatically, then do so yourself and then use the modules by modprobing them

$ modprobe ieee80211

$ modprobe ipw2200

You can add ieee80211 and ipw2200 in your /etc/modules to make sure they load up on boot time

Check that everything works by

$ iwlist scanning

Either eth1 or eth0 should show a list of available wirless networks (if any)

You can create your wirless preferences by modifying your /etc/network/interfaces file. I show a part of mine as reference

Network intefaces file

  mapping eth1
       map home 
       map work
       map none
  # The loopback network interface
  auto lo
  iface lo inet loopback
  # The primary network interface
  # auto eth0
  iface eth0 inet dhcp
  autho eth1
  iface eth1 inet dhcp
  iface home inet dhcp
       wireless-essid enter your wireless ID 
       wireless-key whatever your wirless key is
  iface work inet dhcp
       wireless-essid whatever your work wireleess ID
       wireless-key whatever your wireless key is
  iface none inet dhcp
       wireless-essid ANY
       wireless-key none

Getting power management to work

In my earlier Sony Vaio, I couldn't get ACPI or APM to work. I'm happy to report that in this laptop, I could get power-management to work very well with ACPI. I was able to put the laptop to sleep, and I'm still working on the hibernate feature, although I consider that non-critical. Here is how I got it all to work

ACPI sleep

ACPI sleep worked straight of the bat. Just login as root and type

$ echo mem > sys/power/state

Your laptop should go through the suspend cycle and the sleep light should come on. To resume, press the Fn key and the laptop shoud resume where you left it.

You can automate this whole operation, so that when you close the lid, the laptop should go to sleep automatically. Here's how.

ACPI sleep on lid close script

Add the following in your /etc/acpi/actions directory as lm_lid.sh and make sure that /etc/acpi/scripts/lm_lid points to it. This script was originally taken from Superk.org

  #!/bin/bash
  test -f /usr/sbin/laptop_mode || exit 0
  # lid button pressed/released event handler
  /usr/sbin/laptop_mode auto
  #!/bin/bash
  test -f /usr/sbin/laptop_mode || exit 0
  grep -q closed /proc/acpi/button/lid/*/state
  if [ $? = 0 ]
  then
         chvt 12
         echo mem > /sys/power/state
  else
         sleep 2
         chvt 7

ACPI sleep drain problem

I had this problem also. I located the problem to be the Radeon driver. It turns out that the radeon power mangement source file in the 2.6.12 kernel doesn't put the radeon GPU to sleep during ACPI sleep. You need to patch the kernl to get this to work. The patch as of the time of this writing can be downloaded from OSDL_Bugzilla. Before you do that however, test to see if your laptop is affected by it using this Test script.

If you need to patch the kernel, then the use the following command

$ patch -p0 < radeon_patch_file

Make sure you change the path to your linux sources in the patch file.

I got my power consumption down from 5W during sleep to a very small 300 mW which means I can put my laptop to sleep when fully charged and expect to be on for almost 10 days.

Make sure you add the vide0=radeonfb:force_sleep to your kernel parameter in /boot/grub/menu.lst. Your grub kernel line will look something like this

  kernel          /vmlinuz-2.6.12.2 root=/dev/hda1 ro vide0=radeonfb:force_sleep

CPU Frequency scaling

In debian this is really easy. With your default stock kernel, you can just modprobe cpufreq_userspace and speedstep_centrino and your CPU will dynamically change the frequency to conserver power. Very cool. Most of the time, my processor sits at 599 MHz. Again, add them to /etc/modules to enable them at bootup.

HDD spin down

Again in debian, this is really easy. Just apt-get laptop-mode-tools and powernowd and your HDD will spn down when idle to conserve power. Very cool.

Misc tweaks

You can use the powerplay feature of your Radeon GPU by adding the following in your /etc/X11/xorg.conf

       Section "Device"
          Identifier      "ATI Technologies, Inc. Radeon Mobility M7 LW [Radeon Mobility 7500]"
          Driver          "radeon"
          VendorName      "IBM Thinkpad"
          Option      "DynamicClocks" "on"        
          BusID           "PCI:1:0:0"
       EndSection

Check to see that this is working by looking at /var/log/Xorg.0.log. This feature doesn't work with XFree86.

Hibernate

This for me is non-critical, and I haven't got it working just yet. The way I've tried it so far is by patching the kernel using Software suspend 2. However, the kernel panics on reboot, the reason for which is probably the initrd. I haven't quite figured out how to fix this. I tried making a bzImage kernl although that didn't work either. The kernel doesn't panic in this case but doesn't reusme either. If you have a solution, please edit this and let us all know.

Thinkpad buttons

You can get an online display for your screen brightness and volume control by apt-getting tpb. You need to make /dev/nvram user-writable to get it work with regular user perms. Add tpb to your .xsession file to have it running when you first start X