Search results
Create the page "ETc" on this wiki! See also the search results found.
- ...ation parameter for the default '''pm-utils''' package. Create file <code>/etc/pm/config.d/config</code> and put there one line <code>DISPLAY_QUIRK_S3_BIO echo DISPLAY_QUIRK_S3_BIOS=\"true\" >> /etc/pm/config.d/config16 KB (2,636 words) - 09:33, 23 September 2020
- Then you should setup your displays by hand or by adding to the end of /etc/X11/xinit/xinitrc (just before starting window manager, btw. multi head wm3 KB (271 words) - 14:56, 22 January 2021
- ....0) external vga/ monitor/ beamer works fine with the following in {{path|/etc/xorg.conf}}. I used the free ati driver shipped with Dapper.4 KB (464 words) - 14:49, 22 January 2021
- ...lone mode with a reasonable CRT refresh rate, use the following in {{path|/etc/X11/xorg.conf}}: to the <tt>Device</tt> section in your {{path|/etc/X11/xorg.conf}}. Powering the CRT port consumes 400-500mW, regardless of wh6 KB (901 words) - 14:52, 22 January 2021
- Editing your /etc/modules (may depend on distribution) to auto-load fbmod will result in alwa2 KB (246 words) - 14:56, 22 January 2021
- ...e verification as a human and the necessary account information, passwords etc. I reach a page with the plain message: "Could not open socket". This happe13 KB (2,055 words) - 05:55, 21 July 2011
- ...iver. Install the slmodem rpm from the rpmfusion-nonfree repository, edit /etc/sysconfig/slmodem and set INTERFACE=alsa and ALSA_DEVICE=modem:1 and option8 KB (1,198 words) - 12:30, 7 December 2011
- ...ine) the ALSA intel8x0 driver plays sound too fast. The following {{path|/etc/asound.conf}} restores normal operation: Otherwise just add the following to {{path|/etc/asound.conf}} :3 KB (470 words) - 15:20, 15 November 2020
- /etc/rc.d/init.d/alsa stop /etc/rc.d/init.d/alsa start</pre>2 KB (370 words) - 15:18, 15 November 2020
- The fix changing HIBERNATE_MODE=shutdown to HIBERNATE_MODE=platform in /etc/default/acpi-support worked very well. I don't know if it possibly could in Changing HIBERNATE_MODE=shutdown to HIBERNATE_MODE=platform in /etc/default/acpi-support seems to be solving this issue for many users. Confirm3 KB (466 words) - 15:27, 15 November 2020
- * Select keyboard map, etc, when prompt appears type run_qtparted988 bytes (148 words) - 21:46, 15 July 2010
- :/etc/init.d/hotplug restart10 KB (1,552 words) - 16:56, 16 February 2009
- You may want to put an entry in your {{path|/etc/fstab}}, i.e. with the above assumtions:3 KB (514 words) - 16:38, 22 January 2021
- ...hard drives and some PCMCIA card readers (compact flash, SD, memory stick, etc.) will work for this purpose.14 KB (2,312 words) - 17:13, 7 January 2012
- ...need to have parts outside the slot like wireless antennas, CD-ROM drives etc.) all three types measure the same width and length and they all use the sa4 KB (566 words) - 02:01, 26 September 2005
- ...n X31) I could eliminate these problems by setting the option "vo=x11" in /etc/mplayerplug-in.conf. It seems that the option "vo=xv" causes these problems308 bytes (48 words) - 15:51, 10 July 2005
- ...ration scripts to help load/unload modules, verify hardware, check status, etc. The only thing missing is the firmware. Apparently, this is proprietary a # /etc/init.d/acpid restart2 KB (369 words) - 05:13, 25 October 2006
- ...instead of "set-prop", which required specifying the format (8-bit, 16-bit etc.). # etc.26 KB (3,831 words) - 03:59, 11 May 2017
- Add the dynamic clock option in {{path|/etc/X11/xorg.conf}}. It aims to provide a moderate boost in battery life. The d After compilation, edit {{path|/etc/rc.local}}:4 KB (553 words) - 05:34, 25 October 2006
- *To have this mapping occur automatically, create /etc/systemd/system/wacom-serial.service This may be inserted into startup scripts in {{path|/etc/rc.d/}} or {{path|/etc/rc.local}}27 KB (3,724 words) - 17:02, 22 January 2021
