Problems with SATA and Linux

Some ThinkPad models, use a SATA controller for the system hard disk (the hard disk itself is PATA, but is accessed through a SATA-to-PATA bridge). This causes several complications for Linux installation. The following lists these problems and some workarounds.

Models using a SATA disk interface

SATA controller with IDE disk (PATA passthrough)
ThinkPad T43, T43p, R52, X41, X41 Tablet
SATA controller with SATA disk
ThinkPad Z60t, Z60m.

SATA-related problems under Linux

The following is a list of SATA-related issues one may encounter when runing Linux on these ThinkPad models. Note that the details are often version- and distribution-specific.

Hang on resume from suspend to RAM

Linux kernels (as of 2.6.14-rc2) do not support suspend and resume for SATA devices. As a result, the machine hangs upon the first disk access after resume. A kernel patch is available (see How to make ACPI work under "Suspend to RAM").

Some distributions already include this patch (e.g., Ubuntu), but some don't (e.g., Fedora Core 4).

Failed resume from suspend to disk

Suspend to disk (using swsusp or swsusp2) needs to load the memory image from the SATA disk. For this to work, you either need an initrd with all the necessary SATA modules, or the SATA drivers compiled into the kernel.

DVD drive not recognized

The ata_piix SATA driver grabs ownership over the IDE ports when it is loaded, but (by default) does not support PATA ATAPI devices such as the Ultrabay optical drives. Thus, if IDE support is compiled as a module and loaded after ata_piix, the DVD drive will not be recognized by either driver.

The following configurations do work:

• Compile IDE into the kernel (non-module)
• Compile both IDE and SATA as modules and make sure IDE is loaded first
• Enable PATA ATAPI support in the SATA system (experimental; see below).

Note that the optical drive must be in the Ultrabay during system boot (Ultrabay device swapping is currently unsupported).

No DMA on DVD drive

Using the IDE driver, DMA support cannot be enabled on an UltraBay DVD drive:

# hdparm -d1 /dev/hdc

/dev/hdc:
 setting using_dma to 1 (on)
 HDIO_SET_DMA failed: Operation not permitted
 using_dma    =  0 (off)

As a result, the DVD drive is slow, and in particular, too slow to play video DVDs.

One workaround is to use employ the SATA driver (instead of the IDE driver) for the DVD drive. This requires enabling two featues of the SATA driver, namely ATAPI support and PATA support, which are both in active development and far from stable. Using this will probably devour all your data and go on to eat all the food in your fridge. But if you have full backups and an empty fridge, do the following:

• Grab the latest kernel, since these feature are under active development (these instructions where tested with 2.6.14-rc2).
• Configure the IDE system as modules, to get it out of the way (maybe it can be completely removed).
• Configure the SATA system (and in particular the ata_piix driver) as built-in.
• In include/linux/libata.h, set

#define ATA_ENABLE_PATA

• In drivers/scsi/libata-core.c, set

int atapi_enabled = 1

(An untested alternative to the last step is to compile the SATA system as modules, make sure it is loaded before the IDE modules, and pass the "atapi_enabled=1" module parameter.)

There have been reports that DVD burning doesn't work under this configuration, but it seems to work with kernel 2.6.14-rc2 (tested on a ThinkPad T43 with a UltraBay Slim DVD Multi-Burner Plus).

NOTE!

If you are aware of a more reliable solution to this issue, please update this page.

No SMART support

The Linux SATA system currently does not support SMART commands (e.g., via smartctl). This is under work.

No disk power management

The Linux SATA system currently does not support power management commands. This is under work.

BIOS error 2010 on user-installed hard disk

While not a Linux issue, note that there is an issue with installing alternative PATA (IDE) hard disks as the system drive. Unless the disk is one of the few approved disks listed inside the BIOS, you will get an BIOS error 2010 during system boot, and the disk may operate unreliably. This seems to be enforced due to limitations (bugs?) of the SATA-to-PATA bridge, and currently the only reliably way to avoid it seems to be to use only drives sold by IBM specifically for use in these ThinkPad models.

There is no such limitations for disks used in the UltraBay Slim 2nd Hard Drive Adapter.