How to make use of IrDA
The purpose of this document is to get the IrDA hardware in your ThinkPad operational, setting up communication to other devices is not covered. However, the external links section can prove useful for this.
Contents
Serial IR (SIR)
SIR is limited to serial datarates up to 115.2Kb/s
Kernel configuration
Linux 2.4 kernel config
Edit /etc/modules.conf and add the following lines
alias tty-ldisc-11 irtty alias char-major-161 ircomm-tty
Linux 2.6 kernel config
Edit /etc/modprobe.conf and add the following lines
alias tty-ldisc-11 irtty-sir alias char-major-161 ircomm-tty
Fast IR (FIR)
FIR is the preferred mode of IrDA operation and operates at a bandwidth of 4 Mbps
BIOS settings
Main problem here is that the chips FIR mode needs to be activated. On most ThinkPads, the easiest way to activate FIR mode is by entering BIOS setup during boot-up by pressing F1 when prompted. Then, selecting 'Config' followed by 'Infrared' will allow you to control the IrDA operation. Here you will need to select the option to Enable the infra-red port, and ensure the proper resources are set (typically: IO 0x2f8 and IRQ 3). Be sure to save the changes, and then Exit.
PnP settings from Linux
If changing the BIOS setting is not an option or if the settings cannot be altered, as on some older ThinkPads, the FIR mode can be activated from Linux with one of the following (this needs to be done on every boot):
- setpnp as part of the old pcmcia-utils source package
- tpctl, but only for some old ThinkPads
setpnp requires a kernel with pnp-bios support compiled in, which the Red Hat and Fedora kernels lack.
ISA PnP patch
2.6 kernel ISA PnP Patches exist for the nsc-ircc driver, that allow the loading of the driver without the BIOS, setpnp or tpctl hacks.
You will still have to call setserial and set the dongle_id parameter, as shown below.
This patch seems 'necessaryI in some cases (e.g., ThinkPad T43 and kernel 2.6.14.2).
Kernel configuration
Linux 2.4 kernel config
Edit /etc/modules.conf and add the following lines
alias irda0 nsc-ircc
options nsc-ircc dongle_id=0x09 io=0x2f8 irq=3
pre-install nsc-ircc setserial /dev/ttyS1 uart none port 0 irq 0
Linux 2.6 kernel config
Edit /etc/modprobe.conf and add the following lines
alias irda0 nsc-ircc
options nsc-ircc dongle_id=0x09 io=0x2f8 irq=3
install nsc-ircc /bin/setserial /dev/ttyS1 uart none port 0 irq 0; /sbin/modprobe --ignore-install nsc-ircc
Known problems
- If the FIR mode is not activated, attempts to load the nsc-ircc module will result in an error in syslog of "Wrong chip version ff".
- After suspend the nsc-ircc module needs to be manually reloaded
- If module reloading does not work after a suspend, try reactivating the IrDA port as well:
rmmod nsc_ircc echo disable > /sys/devices/pnp0/00\:0d/resources echo activate > /sys/devices/pnp0/00\:0d/resources modprobe nsc_ircc
- The value pnp0/00\:0d can vary - look for a resources file containing the appropriate irq/dma/io values, e.g., using
# grep 0x2f8 /sys/devices/pnp*/*/resources.
Some other things you might want to do with IrDA
- add fast PPP support:
# modprobe irnet
- if needed, limit further the size of the transmit window
# echo 1 > /proc/sys/net/irda/max_tx_window
LIRC and IrDA
Usually, IrDA port's are not compatible with LIRC, but you may have luck using lirc_sir.
If loading the lirc_sir module shows something like the following in # dmesg output, you are lucky and can use LIRC with the IrDA port to remote control your ThinkPad.
lirc_sir: I/O port 0x02f8, IRQ 3. lirc_sir: Installed.
External Sources
- Linux-IrDA Project (External)
- Linux PCMCIA Project (External)
- tpctl homepage (External)
- Linux Infrared Remote Control (External)
