ThinkPad 11a/b/g/n Wireless LAN Mini Express Adapter
|
This is a WiFi Adapter that is installed in a Mini-PCI Express slot IBM partnumber 42T0825 [1] ContentsFeatures
|
|
Identification
To determine the chipset your card uses, issue the following commands:
# update-pciids # lspci | egrep -i 'network|atheros|wireless' 03:00.0 Network controller: Atheros Communications, Inc. AR5418 802.11a/b/g/n Wireless PCI Express Adapter (rev 01)
If you get something different than above despite having the most current PCI IDs, please report it here!
Linux WiFi drivers
madwifi
For native Linux support, a development snapshot of the "madwifi" driver, which uses a non-free binary-only HAL, can be used. It does not support the draft 11n protocol, but will work in "legacy" 11g mode. Support for this chipset was initially planned for release 0.9.4, but this inclusion had to be postponed as a critical update with a bug fix for compilation with the 2.6.24 kernel was necessary before the pre-release trunk was sufficiently stable. Thus, it is still necessary to download the prerelease snapshot from trunk using subversion.
There is a howto, which describes the procedure for getting the snapshot to work.
There is an old ticket for this card at madwifi, #1001.
There is an new ticket for this card at madwifi-branch, #1243. Insert non-formatted text here
ath9k
There is now active development of a free driver ath9k that is purported to support the draft 11n protocol and is aiming for inclusion in the mainline Linux kernel. If you're impatient and want to try it out NOW, however, you'll have to jump through a few hoops.
Using the Windows Driver in Linux
If you have a weak stomach for pre-release software, you can always use "ndiswrapper" (>= 1.29) to wrap the Windows driver supplied by Lenovo. This isn't as bad as you think. It does work like a charm, but you may have problems if you're using a 64 bit kernel since it's not clear that a 64 bit windows XP driver exists (ndiswrapper currently doesn't support Vista drivers). Here's the Howto.
Problems/Bugs?
Non-Maskable Interrupt with madwifi
A number of folks have reported getting errors while using the experimental madwifi driver with the AR5418. After hours of flawless operation, the Kernel sometimes throws an NMI after which, the wifi dies. Aside from rebooting, suspending (to ram or disk) and resuming seems to be the only method to recover.
Uhhuh. NMI received for unknown reason b0 on CPU 0. You have some hardware problem, likely on the PCI bus. Dazed and confused, but trying to continue
wifi0: rx FIFO overrun; resetting wifi0: rx FIFO overrun; resetting wifi0: rx FIFO overrun; resetting
See the following threads and bug reports: [2] [3] [4] [5] [6]
A possible preventitive measure is issuing the command
# iwpriv <device> bgscan 0
each time you load the driver. To make this change "permanent", you could add this command to your distribution's ifup networking scripts as described below.
Debian
Open up /etc/network/interfaces in a text editor and find the entry for your wireless device. Which should look something like
iface wlan0 inet manual
wpa-driver madwifi
wpa-roam /etc/network/wpa_supplicant.conf
and add the line
post-up iwpriv wlan0 bgscan 0
to the end of it where of course you substitute your interface name (e.g., "ath0") for "wlan0".
Hardware switch
Some ThinkPads have a hardware switch that must be in the on position for the radio to work, regardless of driver state:
In addition to hard-switching the wireless card, the switch also generates an acpi event on transition from hi->lo and vice versa. It is however the same event in both directions.
