Difference between revisions of "SMAPI support for Linux"

From ThinkWiki
Jump to: navigation, search
(→‎Model-specific status)
(→‎Model-specific status)
Line 146: Line 146:
 
|-
 
|-
 
! {{X31}}
 
! {{X31}}
−
| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cunk}} || {{Cunk}}
+
| {{Cno}}  || {{Cno}}  || {{Cno}}  || {{Cunk}} || {{Cyes}}
 
|-
 
|-
 
! {{X32}}
 
! {{X32}}

Revision as of 23:30, 13 December 2005

ThinkPad laptops include a proprietary interface called SMAPI BIOS (System Management Application Program Interface) which provides some hardware control functionality that is not exposed by any other interface (e.g., ACPI).

The SMAPI interfaces changes a lot between models, and is poorly documented, so Linux support is not exhaustive for most models. There are currently two SMAPI access mechanisms available: thinkpad and tpctl for older ThinkPads, and tp_smapi for newer ones.

ATTENTION!
These drivers use undocumented features and direct hardware access. They thus cannot be guaranteed to work, and may cause arbitrary damage (especially on models they weren't tested on).

Using the tp_smapi module

The tp_smapi kernel module exposes some features of the SMAPI BIOS found on recent ThinkPads via a sysfs interface. Currently, the implemented functionality is control of battery charging (this is useful for increasing battery lifetime or for using a leftover under-spec power supply that can't handle the combined power draw of running and charging), and control of CD/DVD speed.

Installation

To compile and load the module: 

# tar xzvf tp_smapi-0.09.tgz
# cd tp_smapi-0.09
# make load

To install permanently (optional): 

# make install
# modprobe tp_smapi

Battery charge control features

To set the thresholds for starting and stopping battery charging (in percent of current full charge capacity): 

# echo 40 > /sys/devices/platform/smapi/BAT0/start_charge_thresh
# echo 70 > /sys/devices/platform/smapi/BAT0/stop_charge_thresh
# cat /sys/devices/platform/smapi/BAT0/*_charge_thresh
40 
70

To unconditionally inhibit charging for 17 minutes: 

# echo 17 > /sys/devices/platform/smapi/BAT0/inhibit_charge_minutes

To cancel charge inhibiting: 

# echo 0 > /sys/devices/platform/smapi/BAT0/inhibit_charge_minutes

Battery status features

To view exteded battery status (see below about conflict with hdaps): 

# cat /sys/devices/platform/smapi/BAT0/installed
# cat /sys/devices/platform/smapi/BAT0/cycle_count
# cat /sys/devices/platform/smapi/BAT0/current1 
# cat /sys/devices/platform/smapi/BAT0/current2
# cat /sys/devices/platform/smapi/BAT0/last_full_capacity
# cat /sys/devices/platform/smapi/BAT0/remaining_capacity
# cat /sys/devices/platform/smapi/BAT0/design_capacity
# cat /sys/devices/platform/smapi/BAT0/voltage
# cat /sys/devices/platform/smapi/BAT0/design_voltage
# cat /sys/devices/platform/smapi/BAT0/manufacturer
# cat /sys/devices/platform/smapi/BAT0/model
# cat /sys/devices/platform/smapi/BAT0/serial
# cat /sys/devices/platform/smapi/BAT0/barcoding 
# cat /sys/devices/platform/smapi/BAT0/chemistry
# cat /sys/devices/platform/smapi/ac_connected

The raw status data, including some fields not in the above (in case you can figure them out): 

# cat /sys/devices/platform/smapi/BAT0/dump

In all of the above, replace BAT0 with BAT1 to address the 2nd battery.

Optical drive control features

To control the speed of the optical drive:

ATTENTION!
Changing the CD speed simultaneously with a read or write to the CD will hang your computer. The hdparm -E or eject -x commands might also work for you, and are safer (but have no effect on some models, such as ThinkPad 43).
Kernel hackers: if you know how to obtain locks that temporarily prevents the ide and ata_piix+libata drivers from touching the drive, or at least how to check whether an ATAPI device is being accessed, please tell the author.
# echo 0 > /sys/devices/platform/smapi/cdrom_speed # slow
# echo 1 > /sys/devices/platform/smapi/cdrom_speed # medium
# echo 2 > /sys/devices/platform/smapi/cdrom_speed # fast
# cat /sys/devices/platform/smapi/cdrom_speed
2

Other features

Other things that can be controlled through SMAPI, but are not supported in this version of the driver, include forcing battery discharge, PCI bus power saving, CPU power saving control and fan control. See the included README file for more information.

Conflict with hdaps

The extended battery status function conflicts with the hdaps kernel module (they use the same IO ports). If you load hdaps first, tp_smapi will disable its battery status functions (and log a message in the kernel log). If you load tp_smapi first, hdaps will refuse to load. Use rmmod to switch between the two.

Some of the battery status is also visible through ACPI (/proc/acpi/battery/*).

The charging control files (*_charge_thresh and inhibit_charge_minutes) don't have this problem.

Model-specific status

tp_smapi feature support matrix
× start_charge_thresh stop_charge_thresh inhbit_charge_minutes cdrom_speed battery status files
(see notice about hdaps above)
G41 yes no yes yes unknown
R40 no no no yes unknown
R50p no no no yes unknown
R51 yes no yes unknown unknown
R52 yes yes yes yes unknown
T40 no no no yes unknown
T40p no no no yes yes
T41 yes no yes unknown unknown
T41p no no no yes unknown
T42 yes unknown unknown yes unknown
T42p yes no yes unknown unknown
T43 yes yes yes yes yes
T43p yes yes yes yes yes
X31 no no no unknown yes
X32 no no no unknown unknown
X40 yes no yes unknown yes
X41 yes yes yes unknown unknown

Please update the above and report your experience on the discussion page. If the module loads but gives a "not supported" or "not implementeded" when you try to use some specific file in /sys/devices/platform/smapi/, please report the dmesg output and whether the corresponding functionality is available under Windows - maybe your ThinkPad just can't do that.

Using the thinkpad module

This solution consists of a module, called thinkpad, and a user-space tool caled tpctl. It provides very rich functionality for older ThinkPads, but on newer ThinkPads much of this functionality is exposed and supported through an ACPI interface and the SMAPI access does not work anymore. Kernel 2.6.9 and newer is unsupported; for kernel 2.6.3 and newer you need tpctl >=4.14 and thinkpad >=5.5. For details, see the README and list of supported models.

Retrieved from "https://www.thinkwiki.org/w/index.php?title=SMAPI_support_for_Linux&oldid=13209"