Difference between revisions of "Problem with USB 2.0"
(→Problem description) |
|||
Line 1: | Line 1: | ||
==Problem description== | ==Problem description== | ||
− | On various (early?) T40 models, USB 2.0 may not function. Symptoms include inability to connect to USB 2.0 devices at USB 2.0 speeds, the "This device can perform faster" pop-up in Windows XP, device ID assignment error messages from the Linux kernel, and frequent reboots of the USB bus and connected devices. | + | On various (early?) T40 models, USB 2.0 may not function, or may function only at USB 1.1 speeds. Symptoms include inability to connect to USB 2.0 devices at USB 2.0 speeds, the "This device can perform faster" pop-up in Windows XP, device ID assignment error messages from the Linux kernel, and frequent reboots of the USB bus and connected devices. |
This is happening on my T41 as well (now), so it's not just limited to early T40 models. | This is happening on my T41 as well (now), so it's not just limited to early T40 models. | ||
Line 6: | Line 6: | ||
==Affected Models== | ==Affected Models== | ||
*ThinkPad {{T40}}, {{T41}} | *ThinkPad {{T40}}, {{T41}} | ||
+ | |||
+ | ==Problem's Cause== | ||
+ | |||
+ | The source of the problem was described by Matthias Himber on the [http://mailman.linux-thinkpad.org/pipermail/linux-thinkpad/2005-June/026884.html linux-thinkpad mailing list] | ||
+ | as follows: | ||
+ | |||
+ | Short answer: your southbridge is about to die, get your system board replaced. Hopefully its still under warranty. | ||
+ | |||
+ | Long answer: a number of Intel chipsets for Pentium IV and Pentium M processors have a design flaw that makes the southbridge (which contains the USB host controllers) especially sensitive to static electricity. As a result | ||
+ | there is a (small) risk that when plugging in or removing a USB device causes damage to the chip. Usually, the first symptom is broken USB 2.0, behaving in exactly the way you described (ie, works under Windows, but only after some waiting and as if it was connected to a USB 1.1 controller, not a USB 2.0 one, and not at all under Linux unless you unload the USB 2.0 driver). This tends to lead to a completely dead chipset a short time later, so better get it serviced NOW. | ||
==Solutions== | ==Solutions== |
Revision as of 07:21, 1 September 2006
Problem description
On various (early?) T40 models, USB 2.0 may not function, or may function only at USB 1.1 speeds. Symptoms include inability to connect to USB 2.0 devices at USB 2.0 speeds, the "This device can perform faster" pop-up in Windows XP, device ID assignment error messages from the Linux kernel, and frequent reboots of the USB bus and connected devices.
This is happening on my T41 as well (now), so it's not just limited to early T40 models.
Affected Models
Problem's Cause
The source of the problem was described by Matthias Himber on the linux-thinkpad mailing list as follows:
Short answer: your southbridge is about to die, get your system board replaced. Hopefully its still under warranty.
Long answer: a number of Intel chipsets for Pentium IV and Pentium M processors have a design flaw that makes the southbridge (which contains the USB host controllers) especially sensitive to static electricity. As a result there is a (small) risk that when plugging in or removing a USB device causes damage to the chip. Usually, the first symptom is broken USB 2.0, behaving in exactly the way you described (ie, works under Windows, but only after some waiting and as if it was connected to a USB 1.1 controller, not a USB 2.0 one, and not at all under Linux unless you unload the USB 2.0 driver). This tends to lead to a completely dead chipset a short time later, so better get it serviced NOW.
Solutions
This seems to be a hardware problem with the USB controller on Intel's chip or related electronics. Sending the laptop in for service may help.
If the Linux kernel refuses to register the USB device, "modprobe -r ehci_hcd" may help. This disables USB 2.0 functionality for the session.