Difference between revisions of "Patch for controlling fan speed"
(→Models on which this patch works) |
(→Models on which this patch works) |
||
| Line 38: | Line 38: | ||
* ThinkPad {{R52}} | * ThinkPad {{R52}} | ||
* ThinkPad {{R50}}<br />Highest manual level is 3; disengage mode works and reaches much higher RPM. | * ThinkPad {{R50}}<br />Highest manual level is 3; disengage mode works and reaches much higher RPM. | ||
| + | * ThinkPad {{X41T}} | ||
* ThinkPad {{X31}} | * ThinkPad {{X31}} | ||
Revision as of 21:58, 28 November 2005
Contents
Overview
This patch extends the ibm-acpi Linux kernel module to control fan speed. It can be used to reduce fan noise (both speed and pulsing) and to decrease fan power consumption.
When this patch is applied and the ibm-acpi module is loaded with the experimental=1 module parameter, the following new capabilities are added to /proc/acpi/ibm/fan:
# echo level LEVEL > /proc/acpi/ibm/fansets a fan speed level between 0 and 7, where LEVEL=0 means fan off and LEVEL=7 is the fastest speed.# echo level auto > /proc/acpi/ibm/fantells the embedded controller to set the fan speed automatically according to system temperatures (this is the default).# echo level disengaged > /proc/acpi/ibm/fantells the embedded controller to disengage fan speed control (see specs below).# cat /proc/acpi/ibm/fanshows the current fan level (in addition to the fan speed in RPM).
For example:
#cat /proc/acpi/ibm/fan
status: enabled
level: auto
speed: 4219
commands: enable, disable, level <level>
(<level> is 0-7, auto or disengaged)
#echo level 2 > /proc/acpi/ibm/fan
#cat /proc/acpi/ibm/fan
status: enabled
level: 2
speed: 3142
commands: enable, disable, level <level>
(<level> is 0-7, auto or disengaged)
This patch is best used with an ACPI fan control script that monitors system temperature and sets the fan speed accordingly.
Models on which this patch works
- ThinkPad T43, T43p
Fan levels (RPM): 1-2 = ~3300, 3-5 = ~4100, 6-7 = ~4700; disengaged mode works. - ThinkPad T42p
- ThinkPad T41
Fan levels (RPM): 1-2 = ~2980, 3-5 = ~3500, 6-7 = ~4050; disengaged mode works at ~5100. - ThinkPad R52
- ThinkPad R50
Highest manual level is 3; disengage mode works and reaches much higher RPM. - ThinkPad X41 Tablet
- ThinkPad X31
Probably many other models.
Models on which this patch doesn't work
- ThinkPad 600E, 600X, 770E, 770X (these use a different fan control interface)
- ThinkPad 560 (these models don't have a fan)
The patch
for ibm-acpi 0.11
This also includes a minor fix (rename of device_add) to make ibm-acpi 0.11 compile on kernel 2.6.13.
--- ibm-acpi-0.11-orig/ibm_acpi.c 2005-03-17 12:06:16.000000000 +0200
+++ ibm-acpi-0.11/ibm_acpi.c 2005-10-26 06:21:57.000000000 +0200
@@ -1488,11 +1488,18 @@ static int fan_read(char *p)
} else {
/* all except 570, 600e/x, 770e, 770x */
if (!acpi_ec_read(fan_status_offset, &status))
len += sprintf(p + len, "status:\t\tunreadable\n");
- else
+ else {
len += sprintf(p + len, "status:\t\t%s\n",
- enabled(status, 7));
+ status ? "enabled" : "disabled");
+ if (status & 0x40)
+ len += sprintf(p + len, "level:\t\tdisengaged\n");
+ else if (status & 0x80)
+ len += sprintf(p + len, "level:\t\tauto\n");
+ else
+ len += sprintf(p + len, "level:\t\t%d\n", status);
+ }
if (!acpi_ec_read(fan_rpm_offset, &lo) ||
!acpi_ec_read(fan_rpm_offset + 1, &hi))
len += sprintf(p + len, "speed:\t\tunreadable\n");
@@ -1506,9 +1513,12 @@ static int fan_read(char *p)
len += sprintf(p + len, "commands:\tlevel <level>"
" (<level> is 0-7)\n");
if (!gfan_handle)
/* all except 570, 600e/x, 770e, 770x */
- len += sprintf(p + len, "commands:\tenable, disable\n");
+ len += sprintf(p + len,
+ "commands:\tenable, disable, level <level>\n"
+ " \t(<level> is 0-7, auto"
+ "or disengaged)\n");
if (fans_handle)
/* X31, X40 */
len += sprintf(p + len, "commands:\tspeed <speed>"
" (<speed> is 0-65535)\n");
@@ -1528,17 +1538,29 @@ static int fan_write(char *buf)
/* 570, 770x-JL */
if (!acpi_evalf(sfan_handle, NULL, NULL, "vd", level))
return -EIO;
} else if (!gfan_handle &&
- strlencmp(cmd, "enable") == 0) {
+ ( (strlencmp(cmd, "enable") == 0) ||
+ (strlencmp(cmd, "level auto") == 0) ) ) {
/* all except 570, 600e/x, 770e, 770x */
if (!acpi_ec_write(fan_status_offset, 0x80))
return -EIO;
} else if (!gfan_handle &&
strlencmp(cmd, "disable") == 0) {
/* all except 570, 600e/x, 770e, 770x */
if (!acpi_ec_write(fan_status_offset, 0x00))
return -EIO;
+ } else if (!gfan_handle &&
+ strlencmp(cmd, "level disengaged") == 0) {
+ /* all except 570, 600e/x, 770e, 770x */
+ if (!acpi_ec_write(fan_status_offset, 0x40))
+ return -EIO;
+ } else if (!gfan_handle &&
+ sscanf(cmd, "level %d", &level) == 1 &&
+ level >=0 && level <= 7) {
+ /* all except 570, 600e/x, 770e, 770x */
+ if (!acpi_ec_write(fan_status_offset, level))
+ return -EIO;
} else if (fans_handle &&
sscanf(cmd, "speed %d", &speed) == 1 &&
speed >= 0 && speed <= 65535) {
/* X31, X40 */
@@ -1751,9 +1773,9 @@ static int __init setup_notify(struct ib
return 0;
}
-static int device_add(struct acpi_device *device)
+static int ibmacpi_device_add(struct acpi_device *device)
{
return 0;
}
@@ -1769,9 +1791,9 @@ static int __init register_driver(struct
memset(ibm->driver, 0, sizeof(struct acpi_driver));
sprintf(ibm->driver->name, "%s/%s", IBM_NAME, ibm->name);
ibm->driver->ids = ibm->hid;
- ibm->driver->ops.add = &device_add;
+ ibm->driver->ops.add = &ibmacpi_device_add;
ret = acpi_bus_register_driver(ibm->driver);
if (ret < 0) {
printk(IBM_ERR "acpi_bus_register_driver(%s) failed: %d\n",
The author disclaims all warranty for this patch, and releases it to the public domain (meaning you may use and further distribute it under any terms you wish, including incorporating it into other software).
for ibm-acpi 0.12a as found in kernel 2.6.14
A slightly modified version which also keeps the lines in the format expected by the gkrellm plugin.
--- drivers/acpi/ibm_acpi.c.orig 2005-11-01 19:47:44.262270250 +0100
+++ drivers/acpi/ibm_acpi.c 2005-11-01 20:16:16.081252250 +0100
@@ -1465,6 +1465,7 @@ static int fan_read(char *p)
{
int len = 0;
int s;
+ char status_read = 0;
u8 lo, hi, status;
if (gfan_handle) {
@@ -1477,9 +1478,11 @@ static int fan_read(char *p)
/* all except 570, 600e/x, 770e, 770x */
if (!acpi_ec_read(fan_status_offset, &status))
len += sprintf(p + len, "status:\t\tunreadable\n");
- else
+ else {
len += sprintf(p + len, "status:\t\t%s\n",
- enabled(status, 7));
+ status ? "enabled" : "disabled");
+ status_read = 1;
+ }
if (!acpi_ec_read(fan_rpm_offset, &lo) ||
!acpi_ec_read(fan_rpm_offset + 1, &hi))
@@ -1487,6 +1490,14 @@ static int fan_read(char *p)
else
len += sprintf(p + len, "speed:\t\t%d\n",
(hi << 8) + lo);
+ if (status_read) {
+ if (status & 0x40)
+ len += sprintf(p + len, "level:\t\tdisengaged\n");
+ else if (status & 0x80)
+ len += sprintf(p + len, "level:\t\tauto\n");
+ else
+ len += sprintf(p + len, "level:\t\t%d\n", status);
+ }
}
if (sfan_handle)
@@ -1495,7 +1506,10 @@ static int fan_read(char *p)
" (<level> is 0-7)\n");
if (!gfan_handle)
/* all except 570, 600e/x, 770e, 770x */
- len += sprintf(p + len, "commands:\tenable, disable\n");
+ len += sprintf(p + len,
+ "commands:\tenable, disable, level <level>\n"
+ " \t(<level> is 0-7, auto "
+ "or disengaged)\n");
if (fans_handle)
/* X31, X40 */
len += sprintf(p + len, "commands:\tspeed <speed>"
@@ -1516,7 +1530,8 @@ static int fan_write(char *buf)
/* 570, 770x-JL */
if (!acpi_evalf(sfan_handle, NULL, NULL, "vd", level))
return -EIO;
- } else if (!gfan_handle && strlencmp(cmd, "enable") == 0) {
+ } else if (!gfan_handle && ( (strlencmp(cmd, "enable") == 0) ||
+ (strlencmp(cmd, "level auto") == 0) ) ) {
/* all except 570, 600e/x, 770e, 770x */
if (!acpi_ec_write(fan_status_offset, 0x80))
return -EIO;
@@ -1524,6 +1539,17 @@ static int fan_write(char *buf)
/* all except 570, 600e/x, 770e, 770x */
if (!acpi_ec_write(fan_status_offset, 0x00))
return -EIO;
+ } else if (!gfan_handle &&
+ strlencmp(cmd, "level disengaged") == 0) {
+ /* all except 570, 600e/x, 770e, 770x */
+ if (!acpi_ec_write(fan_status_offset, 0x40))
+ return -EIO;
+ } else if (!gfan_handle &&
+ sscanf(cmd, "level %d", &level) == 1 &&
+ level >=0 && level <= 7) {
+ /* all except 570, 600e/x, 770e, 770x */
+ if (!acpi_ec_write(fan_status_offset, level))
+ return -EIO;
} else if (fans_handle &&
sscanf(cmd, "speed %d", &speed) == 1 &&
speed >= 0 && speed <= 65535) {
The author disclaims all warranty for this patch, and releases it to the public domain (meaning you may use and further distribute it under any terms you wish, including incorporating it into other software).
Controlling the fan without this patch
If you have the ibm-acpi module loaded with experimental=1, you can control the fan without patching the kernel by directly writing to the relevant embedded controller register using /proc/acpi/ibm/ecdump.
For example:
# echo 0x2F 0x04 > /proc/acpi/ibm/ecdump
will set the fan to manual mode 4 (see the specifications below).
Hardware specs
The patch relies on the following hardware behavior, which was discovered experimentally by Thinker and neither provided by nor confirmed by IBM/Lenovo. The following description may be inaccurate and may vary by model (see list of models above). The terminology probably does not match the one used by IBM/Lenovo engineers.
ACPI DSDT register _SB.PCI0.LPC.EC.HFSP (8 bits, offset 0x2F in the EmbeddedController address space) is read/writable and has the following meaning:
7 6 5 4 3 2 1 0 | | \_________/ | | | | | +--------- manual fan speed level (0=disable, 1=min, ..., 7=max) | +---------------- disengaged (0=normal, 1=disengaged, overrides all) +------------------ automatic fan speed control (0=manual, 1=automatic, overrides manual)
Manual speed levels 8-63 yield the same behavior as level 7, and the the ACPI DSDT uses level 7 for the emergency mode it enters upon critical CPU/GPU temperature, so apparently 7 is the real maximum level.
When bit 7 is on, the embedded controller sets the fan speed automatically according to system temperaturesand some unknown algorithm. This overrides manual control.
When bit 6 is on, the embedded controller does not read the fan RPM (hence EmbeddedController offset 0x84 is not updated), and does not maintain a stable fan speed. This overrides manual and automatic control. When disengaged mode is entered the fan speed is not immediately changed (except if the fan was disabed, in which case it is turned on at a low level). However, once in disengaged mode, fan speed will slowly increase to beyond the maximum manual level (this may cause hardware damage!).
Tools based on this patch or specs
- For Linux: see ACPI fan control scripts.
- For Window: Shimodax's ThinkPad fan control tool (see the forum discussion at thinkpads.com).
